Wall Tiling in Thetford

How To Tile A Wall

If you’re not an expert floor installer who would take wall tile installation as merely being a vertical floor, you are advised to be very cautious when tackling the project. The installation of wall tiles follow some set of rules which you’d better not break if you really wish to protect your investment. And worst of all, a wall tile done wrong is a lifetime penalty of having to look at it. So how can you get it right? Well, probably by reaching out to a wall tile installation professional for a good quality solution that’ll save you time, money and effort. However, we’ve put together this guide to help give you an insight of how it works and also to help you avoid some unnecessary expenses. Let’s have a look!

lHang a batten board

• Start your rows of tiles or bottom-most course with a batten board which works to prevent spillage of tiles.

• Position the batten board at 3/4 of the tiles’ height. Ensure not to start at the floor.

lForm A Pyramid Shape With The Tiles

• If you’ve reached the bottom row of tile, then arrange the tile in a pyramid shape. To achieve this, you’d have to install the tiles one through four as instructed. Each following row will be draped over the pyramid.

lExamine The Floor For Level & Walls For Plumb

• If your floor level or plumb is off by a maximum of a half-inch over the course of 8 feet, add extra baseboards and trim to cover up the problem.

lThe Least Size Of Tiles To Be Used Is Half-Wide

• Ensure that no “silvers (tiles that are lower than half the width of the tile in question) are incorporated in the project.

How To Remove Tile Adhesive From Wall

Do you feel your tile design choices are outdated and want to replace it with a more stylish one? Or perhaps you’re just struggling to remove the old tile adhesive from your wall. Putting on a new wallpaper or repainting your wall might be a cup of tea, but retiling is surely a different experience altogether. After detaching every single piece of tile from the wall, you’ll still have the strongly glued adhesive to battle with. If not done properly, you may as well damage the wall which will trigger a new additional cost for repair. We’d recommend you get a professional helping hand for the best results if you’re without a proper training or experience. However, this guide will teach you everything you need to know about the process. Let’s get started!

Materials Required

• Steamer

• Protective sheets

• 4-inch scraper

• Clean cloth

• Protective gear - face mask, eye goggles, gloves.

Tile Adhesive Removal Process

• Cover The Floor

Ensure that the floor is well covered to collect the residues falling off from the wall with some protective sheets.

• Heat Up The Adhesive

Using the wallpaper steamer, heat up the adhesive to make it a bit loose and softer. Do this by slowly moving the steamer around and ensure not to stay on one spot for too long.

• Scrape Off The Mortar

When you can tell the adhesive is properly softened, use the 4 inch scraper to wipe it off the wall. Do this until all the adhesive has been completely removed.

• Clear Out The Fallen Residue

Clean up any mortar that has fallen on the floor.

After the tile adhesive removal, your wall may need to be skimmed depending on its state. This is to put the surface in a good and flat condition before installing the new tiles. The wall may also need to be re-plastered if the adhesive is extremely strong.

How To Take Tiles Off A Wall

The bonding agent or adhesive usually incorporated to hold a tile against the wall are always very strong or else you’ll find your tiles peeling off. As a result, to have them removed is not the easiest of tasks and bashing them with a hammer, will only have them broken leaving you with the task of having to scrape off the pieces. A better and much easier approach to removing tiles from a wall will be to pry them off one after the other. So how do you go about this? Let’s have a look!

lSafety First, Then Remove The First Tile

• Wear a protective eye goggle and gloves.

• Break up the grout around a tile located atthe wall’s centre using a putty knife and hammer.

• Place the putty knife under the the tile and gently it with the hammer.

lRemove The Remaining Tiles

• By tapping and prying using the tools - hammer and putty knife, wipe off all the tiles in the vertical row.

• Once done, continue to detaching the tiles in the adjacent rows until you’re able to open a wallboard section that’s around 12 inches wide and does not obstruct a stud.

• Use a keyhole blade to poke it through the wallboard.

• With the help of a reciprocating saw, cut out the wallboard’s section.

lCut The Fasteners

• Using a metal-cutting blade, cut te wallboard-holding fasteners. Make sure the fasteners holding the wallboard to the top and bottom plates of the wall are both detached.

lRemove All Wallboard Sections

• Using a similar approach, gently remove the other sections of the wallboard.

• Once completed, you can easily sweep the tiles’ broken pieces.

• Finally, vaccum the grout dust to ensure the work is neatly done.

If you lack a proper training or experience, taking off your tiles from a wall is best left to a skilled professional for the best results and to prevent potential damages which can lead to additional costs.

How To Tile A Kitchen Wall

Tiling a kitchen wall can seem like an easy task until you get started. Errors made will forever be evident for everyone to see unless you’re prepared to spend some extra bucks. When done right, it can actually be a very satisfying project, but don’t even think about rushing into it. If you lack a proper training or experience, it’s advisable to leave the task to a skilled professional for the best results and to avoid extra costs. This guide is meant to give you a detailed insight into the process and help you avoid possible errors.

lPreparation

• Ensure you have the required amount of tiles, adhesive and grout.

• Take the tiles measurement and calculate in square metres.

• Determine the number of tiles to be used and add about 10% to the total number to cover for possible wastage.

• Check to surface to make sure its clean and dry.

lMark Out The Area To Be Tiled

• Mark out the width of the tiles with spacers using a baton of timber.

• Position a tile against the bottom-most point and draw a line.

• Put a baton along this line and follow this by a vertical line at the wall’s end.

lInstall The Tiles On The Kitchen Walls

• Apply an even layer of adhesive with a wall trowel on the kitchen’s wall surface.

• Place the first tile on the adhesive and apply small pressure, do this for the remaining tiles with similar pressure to ensure its levelled.

• Make use of tile spacers to get a uniform space in between.

• Leave the adhesive to harden before applying the grout.

lGrouting

• Remove the tile space and clear out excess adhesive

• Prepare the grout

• Make use of a grout float to apply the mixture into the joints.

• Let the grout dry up a bit before washing the surface off with a sponge and water.