Question 1

How to lay decking?

Accepted Answer

Laying simple, ground-level decking may sound intimidating, but it doesn’t have to be. With careful planning and preparation, you can lay decking that you’ll be proud to show off to neighbours, family and friends. Here are a few tips to get you started. Plan carefully Draw out a plan, to scale, on paper. This will help you to know how many boards you’ll need and ensure that you don’t end up having to cut anything to fit. Prepare the area Measure out the site according to your plan and hammer a peg into each corner, then tie string around each peg to help you see what you’re working with. If you’re not laying on existing slabs, dig into the ground, lifting out turf if it’s there, and check that the site is level. Then add concrete slabs for more stability or lay weed-control fabric over the ground and cover with gravel to further prevent weed growth. Build your sub-frame Since a lot of people ask this, we’ve got a more detailed guide in the FAQ below. Lay your deck boards Start in one corner of the sub-frame and position the first board across the inner joists. You want the deck board in the opposite direction to the inner joists, ensuring that it’s flush with the frame. Position any end-to-end joins between the deck boards halfway across an inner joist so you can screw both boards into the joist for stability. Make sure you keep a gap of between 5-8mm to allow for expansion of the wood. Begin to screw your deck boards to the joists. You’ll need to secure the deck board to every joist is covers along your deck frame. Use two screws for every joist. Mark where you’re going to add your screws, ensuring that they are at least 15mm from the end of the board and 20mm from the outside edges. Drill pilot holes for the screws, being careful to only drill through the deck board and not the joist. Then screw the decking screws into the holes. Continue to screw in the deck boards, ensuring you leave the correct expansion gap. You can stagger the deck board joins across the deck for more strength. Sand down any cut ends if you need to before applying decking preserver to protect the timber from rotting. Although this is a simplified set of instructions, it’s enough for you to see whether you want to attempt to lay decking yourself – and if you don’t, you can get in touch with professionals who will be happy to give you a quote.

Question 2

How to build a deck frame?

Accepted Answer

Building a simple deck frame, or decking subframe, that you’re laying on level ground is easy if you take time to prepare and get all the things you need. We’ll go through the steps on how to build a deck frame here. Tools and equipment To get building your deck frame, you’ll need: Decking joists Coach screws Coach bolts Combi drill Socket set A saw suitable for your project and the thickness of the timber Pencil Decking preservative Sandpaper or sander Build your subframe Measure your deck frame and cut to size if necessary. Make 2 pencil marks on each end of the frame’s 2 outer joists to mark where the coach screws will go. They need to align with the centre of the adjoining outer joist. Then, use a flat wood drill bit to drill recesses into each mark. Make them the same depth of the screws that your using’s head and wide enough for a ratchet or socket to tighten them. Using a thinner drill bit, line up the outer joists and drill a pilot hole through the middle of the recess. These pilot holes act as a guide for the screws and stops them from splitting the wood. Fit the coach screws with either a drill driver or socket and ratchet. Repeat the process for the inner joists once you’ve assembled the outer frame. IMPORTANT: While you’re building your deck frame and the decking itself, remember to cover all pilot holes and ends of timber in decking preservative to ensure that your decking remains structurally sound for as long as possible. Though relatively simple, building a deck frame and the decking will take some time. It would be much quicker and easier to get a professional in to do it, who could represent more value for money.

Question 3

How to fit composite decking?

Accepted Answer

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first. Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Question 4

How to lay decking on uneven ground?

Accepted Answer

There are two ways to lay decking on uneven ground. We’ve explained how to build a raised deck in our FAQ ‘How to build a raised deck’ above, and that’s great for uneven ground or sloped gardens. But there’s another way that you can lay decking on uneven ground if you don’t want a raised deck: you can create a level supporting base. We’ll go through the basics here. Materials you’ll need Paving slabs – old or cheap ones are fine Timber for the frame and legs Type 1 MOT hardcore How to lay decking on uneven ground Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be. Add a 50mm layer of hardcore and make sure it’s compact. Build the decking sub-frame as we describe in ‘How to build a deck frame’. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm. Building your decking on top of paving slabs is a good way to get it level, but you still may not be able to get as good a finish as if a professional did it. If you’re in any doubt, get in contact with some decking specialists and see what they would recommend.

Avg. price low	Avg. price low £1,125
Avg. price	Avg. price £1,500
Avg. price high	Avg. price high £1,725

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Wooden Decking in Swindon

Request Wooden Decking Prices in Swindon

Wooden Decking in Swindon

Average Wooden decking cost in Swindon

Average price per Wooden decking job in 2026

Wooden decking installation cost in Swindon 2026

Wooden decking searches in October 2026

Wooden decking Projects in Swindon in September 2026

17,087

0

0

Wooden decking searches in cities and towns near Swindon September 2026

Wooden decking near you

Swindon

Looking for Wooden decking in Swindon?

Get free quotes from local carpenters

Wooden decking pros in Swindon

Amazing Landscaping Ltd

Latest review

Irene J., BH21

Garden | Decking in Wimborne

Similar Customer Enquiries for Wooden decking in Swindon

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Local & reliable carpenters near me

Tell us about your wooden decking project

Find up to 4 carpenters in Swindon

Hire with confidence

Our reviews

Average

Easy to use

People contact was quick

Got immediate response saved time a ...

FAQs

Other Top Projects in Swindon

Need more help?

Are you a carpenter in Swindon?