Shower Installation in Chislehurst

Is your bathroom sink damaged or old and looking fragile? If yes, then you’re most likely interested in fitting a new one as soon as possible. So how do you go about the installation of a new bathroom sink? This is one of the most frequently asked questions when it comes to bathroom sinks and for a good reason. The fact is, if you’re DIY competent, then this is a task that shouldn’t give you too many hard times. However, if you’re without a proper training or experience, we’d recommend hiring the services of a plumber to guarantee the best results as save yourself some time and additional money which may result from costly errors. In this guide, you’ll learn the steps to bathroom sink installation.

✓ Tap preparation. Apply a small amount of plumber’s mate putty to the base of the taps to be installed.

✓ Install the taps. Identify the taps holes in the sink and squeeze the taps firmly in place, fit the washers and back nuts to the sink’s underside.

✓ Wipe off excess putty. Use a suitable tool to wipe off excess putty that has been pressed out by the tap.

✓ Install the wastage drain. Fit the wastage drain easily into the sink in such a way that the back and front (not side to side) is faced by the two wastage holes.

✓ Tighten the wastage pipe. Squeeze the wastage pipe in, include the washer on the opposite side as well as the nut. Tighten properly with an adjustable spanner and wipe off excess put using a screwdriver or any suitable tool.

✓ Fit the sink to the wall. Put the bolts in position before hanging the sink. Once done, then bolt the sink to the wall and tighten the nut with an adjustable spanner.

✓ Ensure that it’s level with the help of a spirit level.

Are you thinking about installing a new bathroom in your home? One thing that commonly crosses most homeowner’s mind is whether a task can be done by themselves without having to call on a professional for help and in turn, save them some money. So if you’re also thinking along this route, then you’re not alone!

Asides the kitchen, no other home project is probably more involved when talking about the systems as well as skills required. At times, it can be so complicated most expert DIYers will take a deep breathe before carrying out a remodelling job for a bathroom. Basically, bathroom installation will include electrical works, plumbing works as well as tile works which all requires a highly skilled tradesman. It’s the type of work where every square foot counts as it’s a dense, tight work. Apart from that, there are usually some frequent surprises here and there such as identifying rotting joists as well as sub floor underneath a leaking shower or terribly rusted cast iron plumbing stacks. And to round it all up, you’ll also have to deal with the time pressure that comes with a bathroom remodelling project as the room is a highly essential space within the home. As a DIYer you’ll be under immense pressure to get it all over with as soon as possible for continued usage.

The solution to all the problems is simply to call in a professional who can help you manage the project from start to finish. The advantage of this is that you’ll get a good job done and probably in a quicker time than you would have. However, the main reason why most homeowners might not want to hire a pro to handle their bathroom remodelling job is because of money. Ultimately, if you feel confident enough you can go ahead and do the task yourself. If not, then calling in a reliable professional would be your best bet.

Surprisingly, bathroom renovations usually involves a wide range of trades to complete. And to make sure the work is done to a standard accepted by building regulations, some of these trades is required to have some particular legal qualifications. Therefore, if you’re interested in getting a new bathroom project done, you’ll probably need to call in more than just your plumber.

Below are the different trades you may need to successfully install a new bathroom:

✓ Plumber - The plumber’s task would be to install the new bathroom’s pipework and reposition and fit the bathroom items as needed.

✓ Tiler - To remove old tiles ( if any), prepare and tile the walls and/or floor.

✓ Labourer - To detach the old suite, strip out old tiles as well as floor covering etc.

✓ Plasterer - To skim the ceiling or board out the walls before you tile or plaster.

✓ Joiner - To re-hinge doors or construct studwork. For instance, when including a new bathroom to a bedroom.

✓ Painter - To paint the newly skimmed ceiling with the help of anti mould bathroom.

✓ Electrician - To install underfloor heating, ceiling spotlights, an extractor fan or a shaver point.

✓ A builder - A general builder will be required if your new bathroom project requires any structural work to be carried out such as installing a new uPVC window, putting in an RSJ and lots more.

✓ A decorate - As the name suggests, the decorator can come in to make the bathroom look a lot more attractive and to finish the job.

And above all, to ensure proper coordination and success of the project, you’ll also need a person who’ll serve as the lynchpin in charge of the entire project.

Also referred to as bathroom cladding, bathroom wall panels is widely regarded as the easiest way to update the appearance of your bathroom. As there are several design option, it’ll be relatively easy to find one that’ll perfectly fit your bathroom. So if you’ve decided to install new bathroom wall panels one thing you’d probably like to know is whether you’ll need to pay someone a huge sum of money to get the project done. Absolutely not, as long as you’re DIY competent with proper training and experience bathroom wall panel installation is a pretty easy task. All you need do is to cut the shower panels to size and install them to the wall or on existing tiles. However it must be said that hiring the services of a bathroom wall panel installation professional is advisable to guarantee the best results. Now let’s take a loot at the installation steps.

✓ Prepare the bathroom. Ensure that the bathroom walls are degreased, clean and, dust and dirt free. Also make sure that its flat and even with a spirit level.

✓ Make sure a fixing method is in place. If not, make use of treated battens as a fixing method. Fit all battens in such a way that’s plumb and parallel.

✓ Fit the shower tray. Take a measurement of the shower tray to identify the length of the seal strips that is needed while also making room for the shower screen.

✓ Add the seal strips.

✓ Cut the panels to size. Mark the bathroom wall panels and cut to get the right measurement in both height and width. Also ensure to make room for pipe and shower head holes at this point.

✓ Install the panels.