Shower Installation in Redbridge

Once you have your new bathroom installed, or perhaps you’re only replacing the old downlights, you’d probably want to know how to go about fitting your new bathroom downlights. If yes, then you’re not alone! This is a very common question amongst several homeowners and we wish to guide you through once and for all. However, it must be said that if you are not a competent DIYer or probably lack the confidence or skills to pull this off, then it’s advisable to hire a professional to get the best results and also save yourself some money and time.

Here are the list of the tools you’ll need to fit your bathroom downlights: Tape measure, chalk line or laser, pencil, pad saw, hand drill, hole saw and screw drivers.

✓ Measure the bathroom ceiling and mark out the central point of the light which will be where the downlights will be placed. Drill a small pilot hole here.

✓ Check above the ceiling to ensure that there’s no pipes, joists or wires in the way. It’s always a good practice to make sure that there’s sufficient room around where the downlight is to be installed in order to avoid placing it too close to a joist or any other obstacle. You should try as much as possible to maintain a 6 inch gap around the spot where the downlight is placed to make sure the fitting does not overheat.

✓ Use a hole saw or a plasterboard saw to make the cut out for the downlight. Check the downlight’s box for instruction on the size.

✓ Once you’ve been able to make a clean cut ceiling hole, pull through the wiring through the hole so that the downlight can be wired. Once done, then you can fit the downlight into the hole by holding the two springs back against the sides of the downlighter and push up into the hole.

How Much To Tile A Bathroom?

Are you thinking about doing a full renovation or just a facelift of one of the most used rooms in your home - the bathroom? Thanks to its little maintenance requirements, tiling is the most obvious choice for wet areas as well as the popular decoration option for bathrooms. So if you’re planning to tile your bathroom how much is it going to cost?

Just like several other home improvement options, the cost of tiling a bathroom is influenced by a wide range of factors which makes it almost impossible to provide a single, accurate answer to the question. These factors include the size of your bathroom, the materials to be used, the professional tiling company hired and many more.

To calculate the cost of your bathroom tiling, you’ll need to determine the size of the area to be tiled. Simply work out the number of tiles you’ll need by multiplying the width and height and include about 10 percent to cover for possible errors. Generally, tiles can cost from £5 to £20 and more depending on your choice of design. Other materials you’ll have to purchase include tile adhesive, grout and silicone. If you don’t have the necessary tools make sure to get a tile cutter, measuring tape as well as a mixing bucket.

If you want to hire a professional for your bathroom tiling project, you should also consider any work that’ll need to be done before fitting the tiles such as the removal of the old tiles. This can have a great impact on the labour cost, so if you’re intending to save some money you can start by removing the old tiles yourself. Overall, depending on your location and the tiler’s experience can expect to incur about £20 to £40 per square metre. However, some tradesmen can charge a daily rate of about £150 to £200.

Also referred to as bathroom cladding, bathroom wall panels is widely regarded as the easiest way to update the appearance of your bathroom. As there are several design option, it’ll be relatively easy to find one that’ll perfectly fit your bathroom. So if you’ve decided to install new bathroom wall panels one thing you’d probably like to know is whether you’ll need to pay someone a huge sum of money to get the project done. Absolutely not, as long as you’re DIY competent with proper training and experience bathroom wall panel installation is a pretty easy task. All you need do is to cut the shower panels to size and install them to the wall or on existing tiles. However it must be said that hiring the services of a bathroom wall panel installation professional is advisable to guarantee the best results. Now let’s take a loot at the installation steps.

✓ Prepare the bathroom. Ensure that the bathroom walls are degreased, clean and, dust and dirt free. Also make sure that its flat and even with a spirit level.

✓ Make sure a fixing method is in place. If not, make use of treated battens as a fixing method. Fit all battens in such a way that’s plumb and parallel.

✓ Fit the shower tray. Take a measurement of the shower tray to identify the length of the seal strips that is needed while also making room for the shower screen.

✓ Add the seal strips.

✓ Cut the panels to size. Mark the bathroom wall panels and cut to get the right measurement in both height and width. Also ensure to make room for pipe and shower head holes at this point.

✓ Install the panels.

Surprisingly, bathroom renovations usually involves a wide range of trades to complete. And to make sure the work is done to a standard accepted by building regulations, some of these trades is required to have some particular legal qualifications. Therefore, if you’re interested in getting a new bathroom project done, you’ll probably need to call in more than just your plumber.

Below are the different trades you may need to successfully install a new bathroom:

✓ Plumber - The plumber’s task would be to install the new bathroom’s pipework and reposition and fit the bathroom items as needed.

✓ Tiler - To remove old tiles ( if any), prepare and tile the walls and/or floor.

✓ Labourer - To detach the old suite, strip out old tiles as well as floor covering etc.

✓ Plasterer - To skim the ceiling or board out the walls before you tile or plaster.

✓ Joiner - To re-hinge doors or construct studwork. For instance, when including a new bathroom to a bedroom.

✓ Painter - To paint the newly skimmed ceiling with the help of anti mould bathroom.

✓ Electrician - To install underfloor heating, ceiling spotlights, an extractor fan or a shaver point.

✓ A builder - A general builder will be required if your new bathroom project requires any structural work to be carried out such as installing a new uPVC window, putting in an RSJ and lots more.

✓ A decorate - As the name suggests, the decorator can come in to make the bathroom look a lot more attractive and to finish the job.

And above all, to ensure proper coordination and success of the project, you’ll also need a person who’ll serve as the lynchpin in charge of the entire project.