Painting / Decorating in Belfast

How To Prep Walls For Painting

This is exactly the part of a wall painting job that can make or mar the whole project. To ensure that your paint project doesn’t end up being disastrous, the most important place to start is from room preparation which includes cleaning, sanding as well as priming the walls before painting. Not every wall will require to go through all the preparation steps as all walls are unique and some are in better conditions than others. However, it’s advisable to thoroughly inspect the surfaces before you proceed to painting and take the necessary actions where required.

This is a very simple DIY job that should be completed in little time, however it’s also perhaps the most important step of the entire painting project. Hence, if you lack the confidence to pull this off, then we’d recommend employing a painting expert who can guarantee the best results for help. In this guide, we’ll should you how you can prepare your wall for painting.

✓ Cleaning. There is no single best way to properly clean a wall, but most walls will be just fine with a sponge and warm water. For walls that have been stained with oil or grime such as kitchen walls, you can apply grease cutting detergent and water mixture to wash and follow up with warm water to clean the residues and a damp cloth wiping to finish it off. Then leave to dry off properly.

✓ Remove mildrew. Wipe out mildrew using a sponge and solution that’s three to four parts water to one part bleach. Apply this solution and scrub the affected surface with a soft brush.

✓ Sanding. This step is only meant for walls with rough spots on its surface. Dull the uneven spots with a sandpaper, wipe away the dust and leave to dry. Use a fine grit sandpaper to sand the surfaces and let it dry properly.

✓ Priming. Prime the wall to get the most out of your paint. They work to disguise imperfections and create a smooth surface on which you can work on.

How To Paint Skirting Boards

In the exact same way a room isn’t complete unless it has all the right finishing touches here and there, your skirting boards also just wouldn’t be right leaving it without a paint. As you can imagine, skirting board can quickly gather dust, dirt and scuffed over time can affect the appearance of the entire room. But you don’t have to wait for this to happen before painting your skirting boards. Good news is, painting of skirting boards is relatively easy and straightforward especially when you follow the guide given in this article. It should, however, be said that if you’re not so confident about holding a brush and doing the task yourself, then getting a professional painter to complete the project will be a great option to achieve the best result while you can focus on other important things.

Painting your skirting board will help provide your room with the much needed perfect frame. Now let’s take a closer look!

✓ Prepare your skirting boards. Treat your wood skirting board with a knotting solution and wood primer. But if they’re already painted or varnished, simply wipe clean use a wet and dry paper with a mild detergent to abrade the surface. Once done, you can then run a strip of masking tape along the floor.

✓ Start Painting. For the decorative coat, you can use any paint designed for wood and metal like satin, gloss etc. Once selected, you can then start to paint across the top with the help of a 2 inch brush. Then move to the flat side. Work in easy to manage sections and when starting the next section, start at the far side and brush into the section you’ve just painted so as to make for an even finish. Finally, remove the masking tape used before the paint dries off.

Your painter and decorator will carry out most of the preparation work for your project. You can help them by ensuring that the area is clean and tidy. Also, remove as many personal items and pieces of furniture from the area as possible and make sure all your internal doors are firmly closed just in case of dust from rubbing down.

How To Paint A Ceiling

If you’re a bit hesitant to take on the seemingly awkward task of painting your ceiling, you’re definitely not alone. However, there are ways in which you can make ceiling painting tasks one of the less strenuous tasks you’ll find around the house as they’ll help you get rid of most drips and also assist you to easily determine whether or not you’re covering the whole ceiling. In several cases, painting a ceiling simply means painting it white again and most same colour painting jobs are way easier than painting with a new colour entirely. When you have the right size of nap controller as well as the appropriate length of an extension pole, painting over your head will be a lot easier. Here’s how to paint a ceiling.

✓ Prepare the room. This include removing as many furniture and objects from the room as possible while also laying down plastic sheets on the remaining ones. And also cover the floor with paper or canvas drop cloths.

✓ Remove obstructions. Detach or remove everything that can make your work harder like light fixtures or smoke detectors.

✓ Protect surfaces. This includes protecting vertical surfaces like the windows and doors from ceiling paint.

✓ Prepare the ceiling. This involves vacuuming the ceiling to get rid of any dust or dirt, sanding any rough spots on the ceiling with a sandpaper and filling any small holes or cracks in the ceiling (optional).

✓ Prime the ceiling. Use an angled brush or paint edging tool or primer to cut in edges of the ceiling.

✓ Paint the edges of the ceiling. When the primer has dried, simply paint the edges of the ceiling to create a frame in which you can easily work in.

✓ Paint the ceiling in grids.