Find a Renewable Energy Specialist you can trust in Carlisle.

If you’re considering installing ground source heat pump, it’s likely you’re also wondering just how deep it’ll go into the ground to be efficient. Well, the initial step to take while determining the ground source heat pump’s design is to research the different options available to reduce the space heating as well as hot water demand. To achieve this, there must be an accurate measurement of energy efficiency which is usually done by getting an Energy Performance Certificate ( EPC) . This is helpful as such that it helps to identify the most suitable or the right size of heat pumps which will help reduce the consumption of energy, heat loss as well as hot water needs of the house.

Generally, ground source heat pumps are usually more compatible with new builds against retrofits. What’s more? The heat pump has two different types of loop systems :

✓ The open loop system and;

✓ The closed loop system.

The open loop system absorbs water from the ground and transfers this ground water via a heat pump to where it carries out the extraction of heat. Meanwhile the closed loop system extracts heat from the ground and incorporates a continuous loop of piping that’s linked to the indoor heat pump. There are a few types of closed loop system, these includes:

✓ The Horizontal Ground Source Heat Pump. This is installed in horizontal trenches of about 1 to 2 metres deep. This is more common in areas where land is readily available.

✓ The Vertical Ground Source Heat Pump. These boreholes are a more costly option but it’s also the best option when land is not readily available for horizontal installation. The insulation hole is dug at a minimum of 6 metres into the ground, while the entire piping will be at a depth of about 50 to 150 metres based on your home’s heat requirements as well as the ground’s composition.

Biomass boilers do require some maintenance. Many manufacturers recommend servicing twice a year, although this is often included in the installation cost. Many systems have automatic fuel loading that removes the need to manually load fuel. You will need to remove the ash from the boiler, but this is as easy as emptying a vacuum cleaner.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

Solar thermal panels work by capturing heat directly from the sun and using it to heat water. This hot water is then passed through a coil to heat the water for your central heating system. Solar thermal systems are compatible with many existing conventional boilers with hot water tanks, and can be set up to feed in to your existing heating system.

When you’re about to transform from the standard electricity to solar energy, what determines your solar system’s size is the amount of solar that’s required. The amount of solar that you’ll need, on the other hand, requires considering the end goal, be it to increase money savings, reduce environmental contamination, maximize Returns On Investment ( ROI), or just to copy what the neighbour’s done.

In order the determine the number of solar panels that is needed, the first step would be to calculate the number of kWhs that’s currently being used. A kWh is what’s used to determine the amount of energy that has been incorporated over time which the utility uses to bill you. What’s strongly recommended to create a suitable range is a 6 to 12 months average of your household electricity bill. Other factors that can play a key role in the determination of the number of solar panel needed include the following:

✓ Sunlight exposure hours. In order to know just how much energy your solar panels will generate, there’s a need to know the number of direct sunlight hours you should expect on a daily basis. For example if you stay in a region that’s usually very sunny, then it’ll be reasonable to expect more energy production per panel than regions that are usually cloudy.

✓ Angle and size of the roof. Roofs with a lot of workable space may require to let go of some efficiency opting for larger and cost effective panels to achieve the targeted energy. However not all homeowners have sufficient roof space or shade coverage for the solar panel they actually want. Also, the degree at which the roof slants will also determine if the sunlight is hitting the panels well enough and the amount of energy that can be generated thereof.

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

There are two main types of air source heat pump: air-to-water and air-to-air. They work in different ways and have different advantages and disadvantages. Make sure you do your research so you know which one is best for you. Alternatively a registered installer will be able to determine the best type for your property.

Obviously the performance of a solar thermal system will vary depending on the location of the home, the insulation of the property, and your own hot water requirements. Solar thermal panels are capable of providing all of your hot water requirements from April to September. They will still make a contribution to your hot water needs for the rest of the year, but in general you will need a backup system to further heat the water in the colder months.