Find a Roofer you can trust in Betws-y-coed.

How you install commercial rubber roofing is similar to fitting it on a residential property, except that the area that’s covered is likely to be bigger. With commercial properties, you should always leave any maintenance and repair works to the professionals – whether you own or lease the property, you could invalidate any insurance if you try to install rubber roofing yourself. We’ll outline the steps roofers will take when installing rubber roofing on a commercial property.

Firstly, the installers will remove any existing coverings and clean and dry the surface thoroughly. This is vital in ensuring that the rubber will stick. They will then unwrap the EDPM rubber membrane and leave it to rest until it’s fully expanded. On a warm day this may take around half an hour.

Next, the roofers will work with half a sheet of rubber at a time and adhere it to the roof surface. They may use a water-based adhesive which they will spread onto the roof in sections, then roll the membrane onto the surface before moving onto the next section. If they’re using a bonded adhesive, they will apply it to both the roof and the rubber and leave it to dry until it’s tacky before extending the membrane.

Once the EDPM rubber is rolled out, the installers will brush the surface with a large broom to get rid of bubbles and provide a stronger bond. Then they will work of the edges, applying adhesive to roof and walls edges, sealing corners and creating watertight seals. They’ll also tidy up any excess membrane and seal all the trims.

As long as it’s installed correctly, your commercial rubber roofing should last you decades without any repairs needed. It’s always best to inspect your roof regularly to spot any damage before it becomes a bigger problem.

How to repair a flat roof depends on the type of flat roof you have. We’ll talk about how to repair felt, asphalt, fibreglass and EDPM flat roofs yourself. But ultimately if you want the best finish, it’s best to ask a professional to repair your flat roof for you. Repairing a flat roof Whether you’ve got an old pour-and-roll type felt roof or a newer torch-on felt flat roof, you can get cracks, lifting around joints, leaks or dips. As a temporary measure, you can buy a special paint that you paint over cracks. For a more permanent repair, you can add a patch of torched-on felt or add a layer on top. Asphalt flat roof repair As your asphalt flat roof gets older, you may notice blisters, cracks or shrinkage and sagging around flashings. Again, you can use a paint on fix from a tin as a temporary repair, or add heat-applied flashing tape around flashing. For a more permanent fix you can use a liquid system, but many are only available to the trade market. You can also add a patch of torched-on roofing felt over a crack. How to repair a fibreglass (GRP) flat roof Fibreglass flat roofs are usually excellent, but problems can involve leaking flashing and cracks near upstands, trims or board joints. You can add acrylic sealant to cracks or holes for a good DIY repair, but a flashing problem is more difficult to fix. You’ll need to clean and sand the affected area of flashing, then laminate a 600g chopped strand mat into place, cure it and add a topcoat colour to match the roof. That sounds like a job better left to a specialist. EDPM rubber flat roof repair Rubber roofs often suffer from shrinkage when mechanical fixings haven’t been used near upstands, flashing leaks or holes or cuts. If you’ve got a small tear that you want to repair, you can add some lap sealant to the area – but use it sparingly. For a more permanent repair to flashing, buy some self-adhesive flashing that will mould into shape easily. Clean the area you want to repair, add EDPM primer, then stick the patch of flashing on from the centre outwards with a hard roller. You can add lap sealant around the edges if you want more protection from water.

How To Clean And Maintain Metal Roofs

If you already have a metal roof or just planning to get one, you’d probably be interested in knowing the cleaning and maintenance procedures. Although, metal roof are widely known to be very easy to clean and maintain and also very durable and long lasting, it’s still strongly recommended that homeowners should do all in their power clean and to take care of their metal roof in order to ensure it they live up to their potentials. Cleaning your metal roofs regularly helps to minimize damaging element such as airborne dirt, pollen, organic material debris, pollution, mildew and lots more. If left unattended to, these unwanted elements can result in several negative issues over time as such as chalking. Due to fact that metal roofs normally features special coatings as well as paint, cleaning the roof is both easy and environmentally friendly, which removes the need to use toxic chemicals. With just plain water, you can effectively wash down dirt, dust and other debris from your metal roof.

While the cleaning process is quite simple, working at height can be incredibly dangerous. It requires skills and confidence, so if you lack either of these qualities, it’s advisable to call in a professional roof cleaning contractor for help. Below is a simple cleaning solution usful for most metal roofs.

✓ In the event whereby water alone isn’t enough, make a cleaning solution using a quarter cup detergent ( which should include car washing soap, mild laundry detergent, mild dish soap) for each gallon of water.

✓ Apply the mixture to the surface of the roof with a wash cloth and ensure to the application gently.

✓ After application, allow it sit for up to 15mins.

✓ Rinse the roof surface with plain water.

If your existing roof is still in good condition but the membrane is getting old, it’s often not worth exposing the structure to the weather whilst the contractor strips off the old membranes. The contractor will leave them in place to act as a base layer for a new roofing system. As long as there are no other problems with your roof, then overlaying is a good way to replace your flat roof.If you have any more questions about flat roofing that aren’t listed here, fill out our form to ask a contractor.

How to repair a hole in a flat roof depends on what material your flat roof is made from. If you have an asphalt, felt or EDPM rubber roof, the repairs are quite simple, whereas it’s a bit more tricky if you have a fibreglass flat roof. How to repair a hole in an asphalt flat roof If you’ve got a small hole in your asphalt flat roof, you might get away with using a paint-on fix from a tin. It’s best to use this as a temporary measure to tide you over until you can get in touch with a professional. If the hole is on the flashing, you can add heat-applied flashing tape to it, or use a patch of torched-on roofing felt. There are liquid systems you can use, but usually they’re only available to the trade. Repairing a hole in a felt flat roof It's a similar process to asphalt roofing if you want to repair a hole in a felt flat roof. Use a paint-on fix for a temporary solution, but the best way to repair a hole is to use a torched-on piece of roofing felt to cover the hole and make it watertight again. How to fix a hole in an EDPM rubber flat roof If the hole in a rubber flat roof is small, you may be able to get away with applying some lap sealant to the hole. Only use a small amount, as if you go for a more permanent repair later down the line all of this will need to be scraped off. You can also use a malleable piece of self-adhesive flashing – clean the area, add EDPM primer and stick the patch on from the centre outwards. Add sealant to the edges if you want to give it more water protection. How to fix pin holes in a fibreglass flat roof If you find pin holes in your fibreglass roof, it usually means there wasn’t enough resin used at installation. To repair the holes, you’ll need to sand down the entire roof back to the clear resin. Then clean the area with acetone and apply GRP roofing resin – the acetone ensures that the resin sticks. You might need two coats of resin to get rid of all the holes.

The cost for a sun tunnel is affected by 5 key factors:

1. Tube size: Small areas or stairways can gain from a 10-inch size tube, whilst bigger rooms will require a bigger tube. The higher television size, the greater the price.
2. Kind of tunnel and also roof type: You can pick from stiff or flexible tunnels and also domed or flat roofing system panels. Each choice will have a different price.
3. Place: Where you stay in the country will certainly impact the price of your sun tunnel installation. Generally, the higher the living prices in your location, the greater the price of employing an expert will certainly be.
4. Length of the tunnel: Longer tunnels will be charged at a greater price than their shorter equivalents so whether the tunnel runs from the roof to the 2nd or very first flooring will certainly impact the sun tunnel price.
5. Ease of gain access to: Flexible tubes are fantastic for homes where sun tunnels do not run in a straight line from roofing to ceiling. The tubes can then be fitted around challenges in your loft space. Frustratingly, these alternatives do not allow as much light as stiff tubes and also due to their hard setup can be much more expensive.

Tar and gravel flat roofs are popular because the gravel weighs down the surface of the roof so it doesn’t blow away and it also protects it from sun damage. The tar makes the roof watertight, so you won’t get any leaks. However, sometimes problems occur and you’ll get cracks and leaks. So how do you repair a tar and gravel flat roof?

If you notice leaking coming through your flat roof, try to find the source of the leak. Since water can travel easily, it might not be where you think it is. The first place to check is the flashing, then any parts of the roof with gravel missing. Once you’ve found the crack, sweep away any remaining gravel and clean the area.

Apply a primer to the area and allow it to dry. Then, apply a tar and gravel roof patch that you can get from most DIY shops. Patch 2-3 inches around the damaged area, creating layers, and ensuring that there aren’t any air bubbles or gaps. Then you should cover the entire patch with gravel.

Before you try to repair a tar and gravel flat roof yourself, consider how much of the roof needs repairing. Professionals often say that if cracks and faults make up 25% or more of the roof, then you should look to replace it. It might be tempting to try and replace your tar and gravel roof yourself, but it’s best left to the specialists. They will ensure that your new roof is watertight and strong enough to withstand sun damage and storms.

If you’ve never had Velux windows before, you might be wondering how to open them. If you’ve got very high ceilings and your roof windows are set high up in the pitch of the roof, you might not even be able to reach them. So how do you open them in this case?

When Velux windows are installed so high that they’re out of reach, the installers will often recommend that they install an electric switch for you to open and close your windows. They often come with a rain sensor, so you don’t need to rush up to the top of the house if there’s a sudden downpour – they will close automatically. You can also choose to have a remote so you can open and close your roof windows wherever you are in the room.

If you don’t have an electric switch, but you still can’t reach to open and close your Velux windows, you should be supplied with a telescopic pole when they’re installed. If you weren’t or you’ve moved into a home with roof windows and there isn’t one, you can buy them online. They have a hook on the end and can be extended to the correct length so you can hook it over the handle of the window and pull or push to open it.

If you’ve got a top-hung Velux window that can also be opened in a centre-pivot position, it’s easy to switch between the two. Simply ensure the window is completely closed before you start, then open the handle up – but don’t push it out. Then pull the vent bar down until the sash is rotated 180 degrees. Then secure the position by sliding the barrel bolts into the holes at either side of the bottom of the frame. Easy!