Find a Roofer you can trust in Thetford.

The task of installing a tile roof can be quite a difficult one. Such a project takes a great deal of preparation, well before the actual tile installation is done. It does not matter if you are putting new ones or replacing your old tiles, understanding the proper technique and steps become crucial.

Remove old roofing (if applicable).

This is, on its own, a major job that can take days and require special tools. It takes some time, but be prepared to do it right.

Install battens (if applicable).

Battens may be needed to hold the tiles in place if the roof is having a steep slope. Usually made of metal or wood, battens are generally 1 inch thick and run horizontally along the roof.

You can find several varieties of tiles that has a hook or a lip allowing it to hang on the available battens. Apart from this, you can find several clips in the market which help to attach the tiles on to the batten.

Determining the spacing for battens can be done easily using two tiles. To prevent interlocking, a three inch overlap is required at the minimum, and a smaller amount of overhang should be left over the eaves. Keep this in mind when you determine the locations of the battens.

After you have determined the distance between the first two battens, measure the distance and set battens using that spacing up, making sure to double-check measurements as you go along.

• Install the tiles.

• You will need to begin with one side first, and then continue to move along the length of the roof.

• Cut tiles to fit tight spots.

• Tiles have to be cut precisely to overcome any obstacle like the chimney.

• Install the ridge tiles.

After completing the broad surfaces of the roof, special ridge tiles are required to cap the top.

How To Replace Flat Roof Felt

Also referred to as tar paper, roofing felt is installed underneath the roof’s shingles to help deny water access to your home. Installing the roofing felt in overlapping layers builds a water barrier in situations whereby the weather damages or blows away the shingles. Although the application of a roofing felt on a flat roof is relatively easier and safer than working on a peaked roof, it’s advisable to take enough care and precautions. If you lack proper training and experience for this task, we’d recommend you employ a reliable professional to guarantee the best results and save you from further headaches especially in cases whereby unfortunate errors are made. This step by step guide will give you a good insight into the flat roof felt replacement process.

• Take a measurement of the width and length of the roof.

• Calculate the square footage by multiplying the numbers.

• Multiply the square footage gotten by three (it’s advisable to install three layers of roofing felt to create a really strong weather barrier).

• Use a claw hammer to remove the existing roofing felt.

• Use utility knife to cut the new felt to fit the length of the roof.

• Place the first piece along the roof’s edge and use a hammer tacker to tack the felt in place with staples or galvanized nails and hammer.

• Put the staples or nails at every 6 inches along the side touching the roof’s edge as well as down the short sides.

• Repeat the same process for the second piece, laying it out beside the first row of felt.

• Cut a piece of felt to the appropriate length using a utility knife to begin the second layer of roofing felt, and cutting it in half, lengthwise.

• Apply construction adhesive along the first row using a trowel.

• Press the first piece for the second layer onto the adhesive. Repeat this process until the roof is covered with a second layer

• Apply construction adhesive over the second layer to install the third layer. Begin with a full piece of felt without cutting it in half.

• Overlap each piece by 2 inches until you’ve completely installed the third layer.

Most material warranties come from the waterproofing layer manufacturers, and can last between 5 and 20 years. If your roofing contractor is on the manufacturer’s installer list, it might cover their work. It’s important that you always read through all the information given to you about your warranty so you know exactly what is included.

How To Clean Algae Off Roof Shingles

Stains and dirt on asphalt shingles can only make your entire house look shabby which can go a long way to hide away the true value of your building. In some cases, dirts and stains on asphalt roofing shingles are nothing more than a cosmetic issue. However, there are also times in which it goes far beyond this - when the stains are indicators of a problem that if ignored, can result in a serious roof damage and ultimately, roof failure. In most cases, it’s usually hard to distinguish these stains and hence, the more reason why your asphalt roofing shingles should be regularly cleaned and maintained. In this article, we’re going to look at how you can get rid of algae of your roof shingles.

Algae growth on roof usually have either blue, green or black stains. They normally begin with little spots which will develop into streaks overtime. These stains are mostly mistaken for moss or mildew and aren’t harmful to any other thing than the roof shingles. However, the look it gives the entire house is something nobody enjoys.

It should be noted that this is a task that deals with working at height and requires skills and confidence to pull off. If you lack any of these qualities, simply reach out to a professional for help.

✓ Safety first. Put on protective clothing.

✓ Apply a bleach solution with a garden sprayer and let it sit for up to 20 minutes

✓ Rinse the roof thereafter with the stream from the hose (do not use a pressure washer as it can damage the roof shingles)

✓ If there are still algae left after rinsing with water, you can make use of a brush with medium-stiff bristles to gently scrub the stains off. If some stains are still left, simply let the roof dry before repeating the process again.

What Is The Average Cost To Replace A Flat Roof?

Are you interested in knowing how much it costs to replace a flat roof? Here, you’ll discover a price breakdown for replacing flat roof. This includes a number of price determining factors such as materials costs as well as cost of labour and cost per square metre. All these enables you to make easy calculations so that you can determine a flat roof replacement estimate for your own project.

The type of flat roof that is the most common type is the garage roof and for the replacement of a single garage roof, the cost will fall between the range of £700 to £1000. Meanwhile for a double garage, you should expect a price increase of about 40 percent to 50 percent. The main price determinant that’s affecting the price of a new flat roof is the material incorporated in making it. For instance, lead or fibreglass are much more expensive when compared to felt roofs.

Generally, the cost of a flat roof replacement will fall within the range of £700 to £1300 varying largely due to the type of materials to be used by the roofer, the roof’s size as well as whether or not scaffolding would be used. Multiple flat roof applications also comes with different costs which includes:

• Felt roof ( £40 to £60 per square metre).

• Fibreglass roof ( £70to £90 per square metre ).

• Rubber roof ( £80 to £85 per square metre ).

• Lead bay roof ( £90 to £105 per square metre ).

• Fibreglass bay roof ( £40 to £60 per square metre ).

Several professional roofers work in pairs and to hire them you’re likely to be charged between £200 to £300 per day. The project can be completed with just a day’s work, but the installer should be back to make sure there are no leaks.

You should inspect your roof twice a year, ideally after rain or snow, to see if it’s draining properly. Also in the Spring to check for damage that may of been caused over the winter months that will need to be put right before the next winter. Have an inspection carried out if you are unsure.

The cost for a sun tunnel is affected by 5 key factors:

1. Tube size: Small areas or stairways can gain from a 10-inch size tube, whilst bigger rooms will require a bigger tube. The higher television size, the greater the price.
2. Kind of tunnel and also roof type: You can pick from stiff or flexible tunnels and also domed or flat roofing system panels. Each choice will have a different price.
3. Place: Where you stay in the country will certainly impact the price of your sun tunnel installation. Generally, the higher the living prices in your location, the greater the price of employing an expert will certainly be.
4. Length of the tunnel: Longer tunnels will be charged at a greater price than their shorter equivalents so whether the tunnel runs from the roof to the 2nd or very first flooring will certainly impact the sun tunnel price.
5. Ease of gain access to: Flexible tubes are fantastic for homes where sun tunnels do not run in a straight line from roofing to ceiling. The tubes can then be fitted around challenges in your loft space. Frustratingly, these alternatives do not allow as much light as stiff tubes and also due to their hard setup can be much more expensive.