How to make steps for a deck?

Unless you built a ground-level deck, you’re going to need steps to go with it. Check Building Regulations to see if you need to install handrails as well. It’s good practice to: Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm Add a central step riser to stairs wider than 900mm to prevent them buckling Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth Getting started To build your steps for the deck, you’ll need: Step treads (the actual step themselves) Step risers Coach screws Deck screws Saw Drill Make the steps for your deck Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws. After drilling pilot holes, screw the treads into the risers at each end with deck screws. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

How to fit composite decking?

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first. Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Wooden Decking in Axbridge

Obtain Wooden Decking Prices in Axbridge

Wooden Decking in Axbridge

Wooden decking is an increasingly popular option for providing outdoor seating areas in gardens. Due to the natural beauty of wood, they can be very beautiful areas which you can use year round by adding external heating and lighting. Wooden decking is generally fitted in locations in front of patio or French doors where they can create a seamless transition between inside and outside spaces. Wooden decking is available in virtually any size or shape to fit any area. Curved designs or large areas joined by pathways can produce a stunning effect. Wooden decking is relatively simple to install and causes little disruption, particularly when compared to other possibilities like patio or paving. It can even be installed over the top of an existing patio. It is essential however to make sure that your wooden decking is structurally sound and capable of taking the load of any furniture or plants that you want to use on the decking. There is a range of species of wood that can be used in wooden decking. Normally decking is made of hardwood, but there are softwoods available that fulfil the durability requirements. As hardwood decking will require maintenance, which generally requires annual cleaning and staining for weather proofing, composite woods have become popular for use in wooden decking because they are more robust and require much less maintenance.

Average Wooden decking cost in Axbridge

The typical cost of Wooden decking is £1500. Costs can change based upon the materials and the firm hired. The upper price range can be as high as £1725. The material costs are commonly approximately £375

Average price per Wooden decking job in 2025

Avg. price low	Avg. price low £1,125
Avg. price	Avg. price £1,500
Avg. price high	Avg. price high £1,725

£1900

£1425

£950

£475

£0

Prices based on actual Wooden decking costs for Axbridge, as reported by local LeadsDoWork members.

Wooden decking installation cost in Axbridge 2025

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Time frame: 1-4 days

Wooden decking searches in May 2025

Choose your search type

No. of estimated projects Estimates by cities and towns

Wooden decking Projects in Axbridge in April 2025

160

Requests for quotations in Axbridge in April 2025

0

Requests for Wooden decking quotations in Axbridge in April 2025. 0% change from March 2025.

0

Requests for Wooden decking quotations in Somerset in April 2025. 0% change from March 2025.

Source: Numbers calculated based on the search volumes in major search engines

Wooden decking searches in cities and towns near Axbridge April 2025

Wooden decking near you

Choose locations

Towns and Cities near Axbridge Other locations within South West

Axbridge

Axbridge is a village in Somerset, England, in the Sedgemoor district on the River Axe, near the southern side of the Mendip Hills. The town's population according to the 2011 census was 2,057. The town council (which is a church council) has responsibility for neighborhood concerns. The town council assesses local preparation applications and collaborates with the local cops, district council policemans, and neighbourhood watch groups on issues of criminal offense, protection and also website traffic. The community council additionally launches projects for the maintenance and repair of parish centers, and speaks with the district council on the maintenance, fixing as well as improvement of highways, water drainage, paths, public transportation and road cleaning. Preservation matters (consisting of trees and listed structures) and ecological problems are likewise the obligation of the council. Annually participants of the community council elect a mayor for the town. The town falls within the non-metropolitan district of Sedgemoor, which was based on 1 April 1974, under the City Government Act 1972. It had actually belonged to Axbridge Rural District from 1894 to 1974, which was responsible for neighborhood planning as well as building control, neighborhood roadways, council real estate, environmental wellness, markets and fairs, reject collection as well as recycling, burial grounds and crematoria, leisure services, parks and tourism. Somerset County Council is responsible for running the biggest and most pricey local services such as education and learning, social solutions, libraries, highways, public transport, policing and also fire services, trading requirements, garbage disposal and also critical preparation. The town remains in Axevale selecting ward. Axbridge is the most heavily populated location however the ward extends south to Chapel Allerton. The overall ward population as taken at the 2011 census is 4,261. It is likewise part of the Wells region constituency represented in the House of Commons. It chooses one MP by the first-past-the-post system of political election. It is also part of the South West England constituency of the European Parliament, which chooses 6 MEPs making use of the d'Hondt technique of party-list proportional representation.

Looking for Wooden decking in Axbridge?

Get free quotes from local carpenters

Get free quotes

Local & reliable carpenters near me

Tell us about your wooden decking project

Answer a few quick questions, so we can match you with local carpenters who can help.

Find up to 4 carpenters in Axbridge

Get free, no-obligation local wooden decking quotes from 4 verified carpenters working in Axbridge.

Hire with confidence

Compare customer reviews, services and prices, and choose the right tradesperson for you.

Our reviews

Average

Would highly recommend

Would highly recommend, they found me a firm which I was happy with a quote they give me and went ahead and had my job done within 2 days of enquiring.

Good easy way to find a selection of…

Good easy way to find a selection of trades you need all in one place.

Love LeadsDoWork it's a big part of my …

Love LeadsDoWork it's a big part of my Business I would recommend to anyone

FAQs

Unless you built a ground-level deck, you’re going to need steps to go with it. Check Building Regulations to see if you need to install handrails as well. It’s good practice to:

Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
Add a central step riser to stairs wider than 900mm to prevent them buckling
Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

Getting started To build your steps for the deck, you’ll need:

Step treads (the actual step themselves)
Step risers
Coach screws
Deck screws
Saw
Drill

Make the steps for your deck

Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
After drilling pilot holes, screw the treads into the risers at each end with deck screws.
If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards

If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Usually, slipperiness is caused by algae or dirt on top of the deck or terrace. A full cleaning treatment should restore the natural grip of the wood or stone. If slipperiness is a persistent problem, consider installing grip mats in high traffic areas of the deck.

Properly installed wooden decking will not need a lot of maintenance. Most manufacturers recommend regularly brushing leaves and dirt off the deck, and a yearly cleaning and staining procedure. This will keep the wood in the best condition. Fluids and treatments are readily available from all DIY shops and stores.

Other Top Projects in Axbridge

Customer Reviews

Overall rating:

Axbridge Wooden decking installers are rated 4.3 out of 5 based on 7 reviews of 90 pros.

The LeadsDoWork rating and review is an overall rating based on verified reviews and feedback from the customers with Wooden decking projects that have been connected with Wooden decking pros to help them. All Wooden decking contractors All Axbridge Wooden decking contractors

Need more help?

How the 0% VAT Scheme is Making Air Conditioning More Affordable for UK Homes Published: 14/04/2025 If you’ve ever considered installing air conditioning in your home but hesitated because of the cost, there’s now a significant reason to reconsider. Thanks to ... Read this article

Leaking flat roof repair for extension in Wirral Published: 01/03/2025 Need a leaking flat roof repaired in Wirral? Learn about the best solutions, costs, and how to prevent future water ingress. Read this article

Cast iron gutter repair and repainting for church in Derby Published: 01/03/2025 Need cast iron guttering repaired and repainted at your church in Derby? Learn about the process, costs, and how to preserve historic gutters. Read this article

Are you a carpenter in Axbridge?

We can help you get more wooden decking work with our qualified job leads and boost your business.

Join today