Question 1

How to fit composite decking?

Accepted Answer

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first. Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Question 2

How to lay decking on uneven ground?

Accepted Answer

There are two ways to lay decking on uneven ground. We’ve explained how to build a raised deck in our FAQ ‘How to build a raised deck’ above, and that’s great for uneven ground or sloped gardens. But there’s another way that you can lay decking on uneven ground if you don’t want a raised deck: you can create a level supporting base. We’ll go through the basics here. Materials you’ll need Paving slabs – old or cheap ones are fine Timber for the frame and legs Type 1 MOT hardcore How to lay decking on uneven ground Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be. Add a 50mm layer of hardcore and make sure it’s compact. Build the decking sub-frame as we describe in ‘How to build a deck frame’. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm. Building your decking on top of paving slabs is a good way to get it level, but you still may not be able to get as good a finish as if a professional did it. If you’re in any doubt, get in contact with some decking specialists and see what they would recommend.

Question 3

How much decking do I need?

Accepted Answer

How much decking you need will – of course – depend on how big you plan your deck to be. There is an equation to help you work out how many deck boards you need. It’s a little complicated until you’ve been shown how it works, but once you know how to do it it’s easy to work out how much decking you need for any project. The equation takes into account the recommended 10% wastage and includes the expansion gaps that are required, which is between 5-8mm along the length of the deck boards (EGL, or expansion gap length) and 3mm along the ends of the deck boards (EGW, or expansion gap width) for timber. It also assumes you’re laying your decking horizontally, as if you’re looking for a diagonal or chevron design you’ll need more deck boards. Let’s go through an example, assuming you have a 10m x 6m area that you want to cover with decking made from timber boards that are 2.4m long and 144mm wide. We’ll use the EGL of 5mm and EGW of 3mm. Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m2 10 x 6 = 60m2 Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m2 Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m2 / 0.358m2 x 1.1 = 184.36 boards – so round up to 185 so you’re not left short. If that all seems a bit complicated for you, let a professional do the maths – they will be able to give you an idea of how much decking you’ll need in no time.

Question 4

What should I do if my deck or terrace is slippery?

Accepted Answer

Usually, slipperiness is caused by algae or dirt on top of the deck or terrace. A full cleaning treatment should restore the natural grip of the wood or stone. If slipperiness is a persistent problem, consider installing grip mats in high traffic areas of the deck.

Avg. price low	Avg. price low £1,125
Avg. price	Avg. price £1,500
Avg. price high	Avg. price high £1,725

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Wooden Decking in Ayrshire

Find Wooden Decking Prices in Ayrshire

Wooden Decking in Ayrshire

Average Wooden decking cost in Ayrshire

Average price per Wooden decking job in 2026

Wooden decking installation cost in Ayrshire 2026

Wooden decking on Google in Ayrshire

Google searches that showed Local Quotes, 17 July to 14 October 2026

10,380

Wooden decking searches near Ayrshire, 17 July to 14 October 2026

105

28

18

16

Wooden decking near you

Ayrshire

Looking for Wooden decking in Ayrshire?

Get free quotes from local carpenters

Wooden decking pros in Ayrshire

JR Johnstone Roofing & Building

Latest review

Jonathan F., FK8

26th May 2021

Garden Decking in Stirling

Similar Customer Enquiries for Wooden decking in Ayrshire

Garden Decking

Local & reliable carpenters near me

Tell us about your wooden decking project

Find up to 4 carpenters in Ayrshire

Hire with confidence

Our reviews

Average

Easy to use

People contact was quick

Got immediate response saved time a ...

FAQs

Other Top Projects in Ayrshire

Customer Reviews

Need more help?

Are you a carpenter in Ayrshire?