How to build a raised deck?

Building a raised deck will take some time and is trickier than laying standard decking at ground level, but if you want to build decking on a slope or uneven ground it’s the best way to do it. If you do your research and follow instructions, you and a friend or family member can build a raised deck over a few days. Here’s a simplified guide of the steps you’ll need to take. Plan carefully It’s best to plan your raised deck by drawing it to scale on paper before you go and get supplies. This will help avoid wastage and making more cuts to timber than necessary. Prepare the area Prepare the area according to the instructions we give in the FAQ ‘How to lay decking’. However, because you’re building a raised deck, you’ll need to add posts: Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side. Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners. Using a brick bolster, split a concrete block in two. Put a section of the block in each hole. Get a length of post longer than you need and place one in each hole. You can cut it down later. Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props. Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart. Make the outer frame Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be. Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off. Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame. Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame. Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post. Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete. Trim down all the posts to the correct height using a saw. Add your weed-control fabric and weigh down with gravel across the entire area. Add your joists Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support. Attach a joist hanger to each end of the joist. Place the joist in position so the centre lines up with the 400mm spacer mark. Secure using external grade screws once you’re happy that the joist is flush with the frame. Lay your decking boards Refer to our FAQ on how to lay decking to see how you should attach your decking boards. Remember: Always treat cut ends and pilot holes with decking preservative to keep your decking in good condition for as long as possible. Building a raised deck isn’t a straightforward task. If you’d rather leave it to the professionals, get a range of quotes to help you get the best price and a high quality finish.

How to make steps for a deck?

Unless you built a ground-level deck, you’re going to need steps to go with it. Check Building Regulations to see if you need to install handrails as well. It’s good practice to: Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm Add a central step riser to stairs wider than 900mm to prevent them buckling Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth Getting started To build your steps for the deck, you’ll need: Step treads (the actual step themselves) Step risers Coach screws Deck screws Saw Drill Make the steps for your deck Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws. After drilling pilot holes, screw the treads into the risers at each end with deck screws. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

Wooden Decking in Thornton Heath

Wooden decking is an increasingly fashionable choice for providing outdoor seating areas in gardens. Because of the natural beauty of wood, they can be very elegant areas that can be used year round with the addition of external heating and lighting. Wooden decking is commonly fitted in locations in front of patio or French doors where they can create a smooth transition between inside and outside spaces. Wooden decking can come in any size or shape to suit any area. Curved designs or large areas linked by pathways can create an impressive effect. Wooden decking is reasonably simple to install and causes little disruption, particularly when compared to alternatives like patio or paving. It can even be installed over the top of a pre-existing patio. It is necessary however to be certain that your wooden decking is structurally sound and able to take the load of any furniture or plants that you would like to use on the decking. There is a choice of species of wood that can be used in wooden decking. Typically decking is constructed from hardwood, but there are softwoods available that fulfil the durability requirements. As hardwood decking will require maintenance, which typically will involve yearly cleaning and staining for weather proofing, composite woods are becoming more popular for use in wooden decking because they are more robust and require far less maintenance.

Avg. price low	Avg. price low £663
Avg. price	Avg. price £2,050
Avg. price high	Avg. price high £3,363

Avg. price low

Avg. price low
£663

Avg. price

Avg. price
£2,050

Avg. price high

Avg. price high
£3,363

Wooden decking pros in Thornton Heath

Surbiton landscaping and building services in business since 1999 very professional run, family Business that takes pride in their work

Latest review

Paul M., GU2

Garden | Decking in Guildford

Friendly, knowledgeable and got the job done on time. Thanks

Tree surgery services also avaliable Find us on Thomson local and Google

Latest review

Michael F., HA8

Garden | Decking in Edgware

The job was well done, some of the finishing could have been better

If your deck isn’t going to be flat to the ground, it’s a good idea to have some kind of balustrade to avoid any tripping. If the gap between the deck and the ground is less than 600mm, use a 900mm balustrade. If it’s higher than 600mm, the balustrade should be 1100mm tall.

Building a raised deck will take some time and is trickier than laying standard decking at ground level, but if you want to build decking on a slope or uneven ground it’s the best way to do it. If you do your research and follow instructions, you and a friend or family member can build a raised deck over a few days. Here’s a simplified guide of the steps you’ll need to take. Plan carefully It’s best to plan your raised deck by drawing it to scale on paper before you go and get supplies. This will help avoid wastage and making more cuts to timber than necessary. Prepare the area Prepare the area according to the instructions we give in the FAQ ‘How to lay decking’. However, because you’re building a raised deck, you’ll need to add posts:

Place a post in the corner of the frame you created with the pegs and string. Measure and mark out 100mm from each side.
Dig out this soil to a depth of 700mm (watch out for cables or pipes). You should have a 300 x 300mm hole. Repeat for the other 3 corners.
Using a brick bolster, split a concrete block in two. Put a section of the block in each hole.
Get a length of post longer than you need and place one in each hole. You can cut it down later.
Create props on each post to hold them in place until you’re ready to add a cement mix. Check that they’re level. When you’re happy that they are, secure them in place with a concrete mix, making sure you create a slope in the concrete so that rainwater runs away from each post. When the concrete is set, remove the props.
Create a string line around each corner post and find the centre point between each. Place a timber batten at each point, ensuring that they’re not spaced any more than 1500mm apart.

Make the outer frame

Working from the corner where the deck will be at its highest above ground level, measure and mark on the post where the highest part of the frame will be.
Measure from the far side of one post to the opposite and cut sections of joist to size. Line up a piece of joist with the mark you made and temporarily secure it. Factor in a 2mm fall for every metre of decking so rainwater can run off.
Secure the frame to the other corner post, ensuring it’s at the right level. Do this for every side of the outer frame.
Using 100mm coach screws with washers hanging on the end, secure each end of the four sections of frame.
Mark out where the centre of the support posts will be and secure all of these posts to the frame, except the centre post.
Add your central support joists. These should run in the same direction as the deck boards will run. You’ll need to measure from the inside of the frame on one side to the inside of the frame on the opposite side. Attach the joist in the same way as you did for the other posts. Repeat so the centre post is in between two sections of frame and secure the posts with concrete.
Trim down all the posts to the correct height using a saw.
Add your weed-control fabric and weigh down with gravel across the entire area.

Add your joists

Measure 400mm from the centre of the outer frame and mark a line. This will be where the first joist is positioned. Repeat at 400mm intervals down the length of the frame – if the last one will be more than 400mm, add another joist to create enough support.
Attach a joist hanger to each end of the joist.
Place the joist in position so the centre lines up with the 400mm spacer mark.
Secure using external grade screws once you’re happy that the joist is flush with the frame.

Lay your decking boards Refer to our FAQ on how to lay decking to see how you should attach your decking boards. Remember: Always treat cut ends and pilot holes with decking preservative to keep your decking in good condition for as long as possible. Building a raised deck isn’t a straightforward task. If you’d rather leave it to the professionals, get a range of quotes to help you get the best price and a high quality finish.

Yes, although you should make sure that the terrace or decking is able to support the weight of a hot tub. Usually, you will need to have a structural survey carried out on the area. Seek the advise of a hot tub retailer or installer about the logistics of installing one at your property.

Unless you built a ground-level deck, you’re going to need steps to go with it. Check Building Regulations to see if you need to install handrails as well. It’s good practice to:

Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm
Add a central step riser to stairs wider than 900mm to prevent them buckling
Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth

Getting started To build your steps for the deck, you’ll need:

Step treads (the actual step themselves)
Step risers
Coach screws
Deck screws
Saw
Drill

Make the steps for your deck

Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink.
Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws.
Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws.
After drilling pilot holes, screw the treads into the risers at each end with deck screws.
If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Wooden Decking in Thornton Heath

Request Wooden Decking Prices in Thornton Heath