How to fit composite decking?

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first. Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Wooden Decking in Tonypandy

Obtain Wooden Decking Prices in Tonypandy

Wooden Decking in Tonypandy

Wooden decking is an increasingly prevalent option for providing outdoor seating areas in gardens. Due to the natural beauty of wood, they can be very beautiful areas which you can use year round by using additional heating and light. Wooden decking is commonly installed in locations in front of patio or French doors where they can create a smooth transition between interior and exterior spaces. Wooden decking can come in any size or shape to match any area. Curved designs or large areas joined by pathways can produce an impressive effect. Wooden decking is fairly quick to install and causes little disruption, especially when compared to other possibilities like patio or paving. It can even be installed over the top of an existing patio. It is crucial however to make certain that your wooden decking is structurally sound and capable of taking the load of any furniture or plants that you want to use on the decking. There is a variety of varieties of wood that can be used in wooden decking. Commonly decking is constructed from hardwood, but there are softwoods available that fulfil the durability specifications. As hardwood decking will require maintenance, which commonly requires annual cleaning and staining for weather proofing, composite woods are becoming popular for use in wooden decking as they are more robust and require much less maintenance.

Average Wooden decking cost in Tonypandy

The typical cost of Wooden decking is £1500. Costs can change based upon the materials and the firm hired. The upper price range can be as high as £1725. The material costs are commonly approximately £375

Average price per Wooden decking job in 2025

Avg. price low	Avg. price low £1,125
Avg. price	Avg. price £1,500
Avg. price high	Avg. price high £1,725

£1900

£1425

£950

£475

£0

Prices based on actual Wooden decking costs for Tonypandy, as reported by local LeadsDoWork members.

Wooden decking installation cost in Tonypandy 2025

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Time frame: 1-4 days

Wooden decking searches in June 2025

Choose your search type

No. of estimated projects Estimates by cities and towns

Wooden decking Projects in Tonypandy in May 2025

133

Requests for quotations in Tonypandy in May 2025

0

Requests for Wooden decking quotations in Tonypandy in May 2025. 0% change from April 2025.

0

Requests for Wooden decking quotations in Mid Glamorgan in May 2025. 0% change from April 2025.

Source: Numbers calculated based on the search volumes in major search engines

Wooden decking searches in cities and towns near Tonypandy May 2025

Wooden decking near you

Choose locations

Towns and Cities near Tonypandy Other locations within Wales

Tonypandy

Tonypandy is a community and community situated in the county district of Rhondda Cynon Taf, within the historic county borders of Glamorgan, Wales, depending on the Rhondda Fawr Valley. A former commercial coal mining town, today Tonypandy is best called the website of the 1910 Tonypandy riots. Tonypandy indicates fulling mill lea, from Welsh ton (antiquated tonnau) for lea, layland, field, grassland or unploughed land; pannu for fulling as well as ty for house (cf. pandy).

Looking for Wooden decking in Tonypandy?

Get free quotes from local carpenters

Aberdare - CF44

Enquiry from: Moyra R

Start Date: Immediate

Customer visited the mygardeningprices.co.uk site and submitted an enquiry. Property type: Detached, Work description: Replace existing fencing and decking.

Post a similar request >

Local & reliable carpenters near me

Tell us about your wooden decking project

Answer a few quick questions, so we can match you with local carpenters who can help.

Find up to 4 carpenters in Tonypandy

Get free, no-obligation local wooden decking quotes from 4 verified carpenters working in Tonypandy.

Hire with confidence

Compare customer reviews, services and prices, and choose the right tradesperson for you.

Our reviews

Average

Would highly recommend

Would highly recommend, they found me a firm which I was happy with a quote they give me and went ahead and had my job done within 2 days of enquiring.

Good easy way to find a selection of…

Good easy way to find a selection of trades you need all in one place.

Love LeadsDoWork it's a big part of my …

Love LeadsDoWork it's a big part of my Business I would recommend to anyone

FAQs

How much decking costs depends on the type of material you go for, how big you want your decking to be and where you live in the country. But typically, the cost of decking is between £1,200 - £1,800. The most popular material for decking is pre-treated softwood, which will set you back around £1,000 for 15m². Hardwood is more expensive but is more durable, and will cost approximately £2,000 for the same amount. Homeowners are also beginning to choose composite decking, which is made from recycled plastic and wood fibres, and is low-maintenance and eco-friendly. This will cost around £1,600 for 15m², while uPVC which is also a low-maintenance option costs around £600. People tend to choose composite over uPVC because it looks more like natural timber. If you’re a competent DIYer, you might want to have a go at laying decking yourself which will set you back around £1,000 for a standard softwood timber deck. We think it’s worth paying the extra £600 for a professional to lay your decking, since they will be able to do it much more quickly. If you do want to try it yourself, we recommend leaving at least a whole weekend open to do it, but it’s likely to take you longer. Factor in the possibility of having to take time off work to complete it and it might be more cost-effective to leave it to the pros.

Properly installed wooden decking will not need a lot of maintenance. Most manufacturers recommend regularly brushing leaves and dirt off the deck, and a yearly cleaning and staining procedure. This will keep the wood in the best condition. Fluids and treatments are readily available from all DIY shops and stores.

How much decking you need will – of course – depend on how big you plan your deck to be. There is an equation to help you work out how many deck boards you need. It’s a little complicated until you’ve been shown how it works, but once you know how to do it it’s easy to work out how much decking you need for any project. The equation takes into account the recommended 10% wastage and includes the expansion gaps that are required, which is between 5-8mm along the length of the deck boards (EGL, or expansion gap length) and 3mm along the ends of the deck boards (EGW, or expansion gap width) for timber. It also assumes you’re laying your decking horizontally, as if you’re looking for a diagonal or chevron design you’ll need more deck boards. Let’s go through an example, assuming you have a 10m x 6m area that you want to cover with decking made from timber boards that are 2.4m long and 144mm wide. We’ll use the EGL of 5mm and EGW of 3mm.

Calculate the surface area for your decking Multiply the length (L) of your decking area by the width (W): L x W = Decking Surface Area (DSA) in m² 10 x 6 = 60m²
Work out the coverage of your deck boards Add your deck board width (DBW) to the expansion gap length (EGL), then add the deck board length (DBL) to the expansion gap width (EGW). Then multiply these numbers. (DBW + EGL) x (DBL + EGW) = Single Board Coverage (SBC) 0.144m + 0.005m = 0.149m 2.4m + 0.003m = 2.403m 0.149 x 2.403 = 0.358m²
Calculate the number of deck boards you need Multiply the SBC by 1.1 to allow for 10% wastage. Then, divide the DSA by the SBC. DSA / SCB x 1.1 = Total number of boards required 60m² / 0.358m² x 1.1 = 184.36 boards – so round up to 185 so you’re not left short.

If that all seems a bit complicated for you, let a professional do the maths – they will be able to give you an idea of how much decking you’ll need in no time.

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards

If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia.
Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws.
Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist.
Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3.
Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first.

Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Other Top Projects in Tonypandy

Customer Reviews

Overall rating:

Tonypandy Wooden decking installers are rated 4.7 out of 5 based on 2 reviews of 73 pros.

The LeadsDoWork rating and review is an overall rating based on verified reviews and feedback from the customers with Wooden decking projects that have been connected with Wooden decking pros to help them. All Wooden decking contractors All Tonypandy Wooden decking contractors

Need more help?

How the 0% VAT Scheme is Making Air Conditioning More Affordable for UK Homes Published: 14/04/2025 If you’ve ever considered installing air conditioning in your home but hesitated because of the cost, there’s now a significant reason to reconsider. Thanks to ... Read this article

Leaking flat roof repair for extension in Wirral Published: 01/03/2025 Need a leaking flat roof repaired in Wirral? Learn about the best solutions, costs, and how to prevent future water ingress. Read this article

Cast iron gutter repair and repainting for church in Derby Published: 01/03/2025 Need cast iron guttering repaired and repainted at your church in Derby? Learn about the process, costs, and how to preserve historic gutters. Read this article

Are you a carpenter in Tonypandy?

We can help you get more wooden decking work with our qualified job leads and boost your business.

Join today