Question 1

How to make steps for a deck?

Accepted Answer

Unless you built a ground-level deck, you’re going to need steps to go with it. Check Building Regulations to see if you need to install handrails as well. It’s good practice to: Have a step tread width of 900mm – if you don’t want them that wide, they should be no less than 760mm Add a central step riser to stairs wider than 900mm to prevent them buckling Add a step depth (the vertical distance between each step) of between 150 and 180mm if building your own riser, so the steps are at a comfortable depth Getting started To build your steps for the deck, you’ll need: Step treads (the actual step themselves) Step risers Coach screws Deck screws Saw Drill Make the steps for your deck Make sure the ground where you want to put your steps is level and firm. If it’s not, consider laying concrete or paving slabs to provide a secure surface for your steps to sit so they don’t sink. Grab some joist off-cuts and cut them to the same width as your step treads. Attach them to the step risers at the top and bottom using countersunk coach screws. Place the steps against the sub-frame of the deck; if you’ve put slabs down for support, make sure the steps sit in the middle of them. The longest edge of the stair riser should be on the slabs, and the short edge against the deck. Drill pilot holes through the step and sub-frame joist, then screw the step to the sub-frame with more coach screws. After drilling pilot holes, screw the treads into the risers at each end with deck screws. If you don’t want gaps between each stair, you can add joist off-cuts or deck boards. Measure the height and depth of the gap, then screw the off-cut or board into the step riser with two screws at each end.

Question 2

How to build decking on a slope?

Accepted Answer

You might think that building decking on a slope is a no-go, but it’s actually a great way to help you make use of your garden when the ground is sloping. It will provide you with a level surface that you can BBQ on as well as dine alfresco without finding that your meal is rolling down the table. But how do you build decking on a slope? Our guide in the FAQ above, ‘How to build a raised deck’, is the perfect solution – but we’ll break it down here if you just want to get an idea of what’s involved. Dig out the area If you’re laying on soil or turf, you’ll need to dig it out. Dig down and remove all the turf from the area and ensure that there are no weeds or stones in the area you’re going to build your decking on. Since you’re building on a slope, it will be hard to get it level, but dig out to a depth of 50mm and lay weed-control fabric with gravel over the top. Add posts and set with concrete Make holes for posts and add them in, ensuring they’re longer than you need. Make sure they’re level, then fill the holes with a concrete mix to set them in place. Build the outer frame Make sure you always work at the top of the slope when you’re building your decking, and measure where the highest point of the decking will be. Secure the 4 sides of the outer frame and factor in a 2mm fall for every metre of decking so rainwater can run off. Add joists Secure joists along your frame at 400mm intervals. If you get to the last joist and there will be more than a 400mm gap left at the end, add in an extra one for support. Lay your deck boards Screw your deck boards to the joists, ensuring that the deck boards are running in the opposite direction to the joists. For timber boards, you need to make sure you leave an expansion gap of 5-8mm. These steps should give you an idea of whether you want to have a go at building decking on a slope, or whether you want to leave it to the pros.

Question 3

How to fit composite decking?

Accepted Answer

Fitting composite decking is similar to installing timber decking, but there are some small differences in terms of the gaps you need to leave between boards and the screws you use. We’ll go through a quick guide to show you the process involved in fitting composite decking so you can decide whether it’s something you want to do yourself. Prepare the area Prepare the area according to our instructions in the previous FAQs – or you can use an existing patio or concrete base if you have one. Measure and mark out the area using chalk (if using an existing base). Assemble the decking frame Build the outer frame as we show in our FAQs above; if the area you have planned is longer than your joists, you’ll need to join them together. When you’ve built the frame and it’s secure, ensure that it’s at the right level for water runoff and add risers, slabs or treated off-cuts of timber at 500mm intervals if you need to. Add joists The spacing of your joists will depend on the type of design you have chosen for your composite decking. If you’re laying arched boards horizontally, you’ll need to space the joists 300mm apart. Lay your composite decking boards If you’ve not got an overhang or it’s a fixed deck, fit starter clips along the outside edge of the frame and secure with screws provided with the composite decking. If you are working with an overhang, put the first board into position not exceeding 25mm. If you’re adding a fascia, put an off-cut of board under the overhang so you know it’ll be flush with the fascia. Pre-drill all fixing points, measuring in 30mm from the edge of the board. Secure the board to the joist below with composite decking screws. Slide a hidden fastener clip in so it sits within the groove of the deck board. It needs to be in the centre of the joist to keep the boards secure and ensure an expansion gap of 6mm. Tighten the clips until just tight, and repeat so there’s a clip at every joist. Add the next board, ensuring that the fastener clips sit within the groove – make sure you don’t force it. Repeat step 3. Continue steps 3 and 4 until you’re at the final board, which you should secure in the same way as you did the first. Add a fascia board If you’re adding a fascia, measure in 40mm from each end and add two guide marks: one at 40mm from the top and the other at 40mm from the bottom. Connect the marks, then mark at 300mm intervals down the board. Drill pilot holes, then put the fascia board into position. You need to make sure that there’s a 40mm ventilation gap between the bottom of the fascia and the ground. Ask someone to hold the board level until you’ve finished securing it with composite decking screws; you can get colour-matched ones so they don’t look unsightly at the end of your decking. Not so sure you want to carry out such a big project yourself? Get quotes from decking pros who will be able to fit composite decking much more quickly and easily.

Question 4

How to lay decking on uneven ground?

Accepted Answer

There are two ways to lay decking on uneven ground. We’ve explained how to build a raised deck in our FAQ ‘How to build a raised deck’ above, and that’s great for uneven ground or sloped gardens. But there’s another way that you can lay decking on uneven ground if you don’t want a raised deck: you can create a level supporting base. We’ll go through the basics here. Materials you’ll need Paving slabs – old or cheap ones are fine Timber for the frame and legs Type 1 MOT hardcore How to lay decking on uneven ground Mark out the area as we explain in ‘How to lay decking’. Then, dig to 200mm below where you want to surface of the decking to be. Add a 50mm layer of hardcore and make sure it’s compact. Build the decking sub-frame as we describe in ‘How to build a deck frame’. Lay out paving slabs along the edges and in the centre of the area. This will help to spread the weight of the decking. Set the decking frame on the slabs, checking for high or low points and adding off-cuts of timber where needed. Don’t forget to sand and seal these off-cuts with decking preservative. Add your joists and then the deck boards, leaving the recommended gaps of expansion of between 5-8mm. Building your decking on top of paving slabs is a good way to get it level, but you still may not be able to get as good a finish as if a professional did it. If you’re in any doubt, get in contact with some decking specialists and see what they would recommend.

Avg. price low	Avg. price low £663
Avg. price	Avg. price £1,300
Avg. price high	Avg. price high £1,863

	Labour cost	£1,050
	Material cost	£375
	Waste removal	£75

Wooden Decking in Wolverhampton

Discover Wooden Decking Prices in Wolverhampton

Wooden Decking in Wolverhampton

Average Wooden decking cost in Wolverhampton

Average price per Wooden decking job in 2026

Wooden decking installation cost in Wolverhampton 2026

Wooden decking searches in June 2026

Wooden decking Projects in Wolverhampton in May 2026

5,222

0

0

Wooden decking searches in cities and towns near Wolverhampton May 2026

Wooden decking near you

Wolverhampton

Looking for Wooden decking in Wolverhampton?

Get free quotes from local carpenters

Similar Customer Enquiries for Wooden decking in Wolverhampton

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Garden | Decking

Local & reliable carpenters near me

Tell us about your wooden decking project

Find up to 4 carpenters in Wolverhampton

Hire with confidence

Our reviews

Average

Would highly recommend

Good easy way to find a selection of…

Love Local Quotes it's a big part of my …

FAQs

Other Top Projects in Wolverhampton

Are you a carpenter in Wolverhampton?