Block Paving in Heckmondwike

One thing you should know about block paving a drive is that it can be very expensive depending on a number of factors such as the materials to be incorporated, block paving pattern, labour cost as well as the size of the drive in question. However, before you get started it’s always a good idea to obtain multiple quotes to compare the prices and select the most reasonable quote. Here, we’ve provided a breakdown of the block paving cost to ensure that you’ll not get ripped off.

There are three main types of block paving which includes clay blocks, concrete blocks as well as natural stone. If you were to go for complex block paving patterns and extras such as drainage solutions and edging, you may have to pay a significantly higher price. The size of your drive is also a major determinant of your block paving cost. What’s more? The materials you need as well as the contractors you select will all play a key role in the final cost of block paving your drive.

The material cost for the three types of block paving includes: Clay block £70 to £100 per m2, concrete blocks £20 to £60 per m2 and natural stone £50 to £105 per m2. To calculate your total material cost, you’ll need to determine the size of your drive.

The cost of labour for installing block paving is usually within the range of £50 to £100 per square metre. In certain cases, you may also have some waste removal needs. If you’re going to hire a specialist that’ll take a day or two of labour to get the job done, it’ll cost about £150 to £200 per day.

Other additional block paving costs include: hardcore £300, blocks and edgings £1,700, sharp sand £250. kiln-dried sand £250 and skip hire £500.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.

Are you having weed problems on your carefully picked out block pavings? After spending huge bucks to install the block pavings, the last thing any homeowner would want to discover is weed taking over the prized asset. Fortunately, this is a problem that can be effectively handled in a few simple steps provided in this article.

Basically, sealing of block paving is all about prevention of weed growth in the area by total weed removal, putting of sand between the block paving joints and sealing with a good quality sealant. This is a task that’s best left for a reliable professional to guarantee the best results especially if you lack proper training and experience. This guide will give a good insight into the process.

Here are the equipment you’ll need to get started: pressure washer, weed killer, bin bag, broom, small brush, protective gear, sealing roller, spueegee, jointing sand and sealer and DIY sprayer.

lRemove The Weed

• Put on a protective clothing and gloves

• Get a weed disposal bag to clean while you go.

• Apply the selected weed killer on both areas where weeds are present and the absent ones to prevent any growing.

lPressure Washing

• Angle your pressure washer between the gaps. This is done to remove all weeds and debris that are still lying around as well as removing all possible chemical residues to create a thorough clean between the paving slab.

• Leave the washed area to dry.

l Sand The Joints

• Check the weather forecast to ensure there’s about 24 to 48 hours of dryness as its important for both sand and sealant to do a perfect job.

• Put sand between the gaps and push it down with your small brush until its levelled.

lSeal The Gaps

• The sealing process should be done immediately and sanding.

• Clean up the patio

• Perform a test using a small area

• Apply the sealant

• Apply the second of sealant

• Leave to dry for about 2 to 3 hours.

Are you worried there’s a slope on the area where your block paving is to be installed? Good news is, it’s very possible to lay block paving on a slope. However, this can be a very difficult task which should be done by a reliable professional ( especially if you lack proper training and experience) who can guarantee the best results, the first time and also help save you money from possible costly mistakes. This guide will provide you with everything you need about the slope block paving installation process. Let’s have a look!

• Demarcate The Walkway

To get started, you have to determine how and where you want your walkway to be while also determining the thickness of the paver. Ensure to choose the less sloppy area and utilize landscape paint to mark the area visibly.

• Prepare The Ground

Clear out all forms of dirts, roots, rocks and other debris on the soil. Once done, proceed to cutting the sods to the required length and put them somewhere close.

• Make Boundaries

There’s a need for landscape borders. Here, it’ll be easier to use plastics as boundaries for your lawn’s edges. Install them on the sides that have already been cut

• Apply A Level Of Gravel

Obtain the correct size of gravel and spread them evenly over the area to ensure a firm foundation for the pavers is formed. Makes sure that the rocks is at a minimum of 2 inches deep into the soil.

• Install The Block Pavers

Start from the centremost position of the pathway and work towards the sides until you’re able to cover every inch of the area.

• Apply A Layer Of Cement

Apply cement over the pavers and utilize a broom to sweep it and fill up all the gaps and spaces between the pavers. Then, press the pathway to be levelled using a compactor.