Driveway Repair in Camden

Pitting, also referred to as spalling is the event whereby “pits” or small holes start showing on the surface of your concrete driveway which makes it appear both worn and uneven. Concrete driveway pitting is a common but highly frustrating problem for most homeowners. You’ll see some concrete driveways that’ll only start to pit after a couple of years, but this is not true for all concrete driveways as others will start to show signs only after a couple of months. So how do you tackle this issue? Well, it’s relatively simple to tackle, however if you’re not confident or lack the necessary skills, we’d recommend you get in touch with a reliable professional who can guarantee the best results for help. In this guide, we’ll take you through the concrete driveway pitting repair process.

✓ Prepare the pits by cleaning the area, clearing out all debris and more. The small pits can be cleaned with a stiff brush while a sturdy broom will do a good job for larger pits.

✓ Make use of a hose to spray the concrete pits and flush out all remaining bits of waste.

✓ If you’re tackling series of small pits, simply use a caulking gun filled with pre-mixed epoxy and specially formulated for concrete to fill the pits. Clear off the excess eproxy ensuring that its level with the concrete surface. Once done, simply leave for at least 24 hours before the application of a concrete sealant to prevent the wear and tear of the new concrete.

✓ Chisel out a little concrete and clean with a pressure washer. Once done, apply a concrete resurfacing compound mixture into the holes and use a trowel to level off.

✓ Ensure that the repaired concrete driveway is protected from rain and foot traffic for at least 6 hours (or 24 hours for vehicles).

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

A patio is an outdoor space which can be used for a variety of stuffs which includes fun time with family and friends, reading time or just relaxing as the fresh breeze blows. With all these benefits and more, it’s becomes more obvious that there’s a need to keep your patio in a tip top condition at all times. If otherwise, you may not be able to enjoy your patio to your satisfaction and probably, for as long as you would want. You simply have to provide it with a regular maintenance which involves inspecting and identifying the damages that needs to be repaired before it gets out of hand. Fortunately, the minor repairs can be done by yourself if you’re confident enough. However, for bigger damages it’s advisable to call in a professional for help. In this article, we’ll take you through the patio reparation process.

✓ Prepare the area. This involves removing the problem piece gently and carefully. If there’s a piece you think can still be useful, store it in the re-use pile or you can start a new one. Once you’re done removing the pieces, the next thing to do would be to start removing anything that’s unwanted from the damaged area like debris, unwanted soil etc, and start sand fitting with some fresh sand. This should be levelled out to ensure there’s no bumps.

✓ With the sand down, you can start by putting the pieces back in together. This should be done gently to avoid any further damage. Do this until your patio

✓