Resin Driveway in Telford

The best way to clean resin bound driveways is to sweep it regularly with a stiff broom. This will remove any debris and prevent moss from growing. It's a good idea to jet wash it after sweeping, because this will get rid of any smaller parts that a broom might not collect.

When you jet wash or power wash your resin bound driveway, make sure the pressure isn’t too high. It’s recommended to keep the pressure less than 150bar, as anything too strong could damage the surface. Make sure the water is cool, but not cold – both hot and cold water can damage the resin. Make sure the jet wash nozzle is at least 20cm from the surface. Any closer and this could damage your driveway. Use a sweeping back and forth motion to clean.

If you treat the area before you have your resin bound driveway installed, you shouldn’t get any weed growth. But if you get any moss or algae appear, you can apply a moss and algae killer that should remove and prevent any regrowth. If you have ingrained algae, you can remove it with a strong bleach solution; make sure you follow the manufacturer’s instructions. This should also help restore the driveway’s original colour. Make sure you rinse your driveway thoroughly with clean water after using bleach on it to prevent any harm to wildlife or plants.

If you get chewing gum on your resin bound driveway and you can’t get it off with a pressure washer, try using a freezing spray on it first. Then use a wall scraper to gently remove it – never dig under the chewing gum as this could damage the resin on your driveway.

Whether you think resin bound driveways are expensive or not will depend on your perception. While resin bound driveways are the most expensive up front, they should last much longer than other types of driveway. You should expect a resin bound driveway to last at least 25 years, if not longer, while a concrete or asphalt driveway may last between 15-20 years. A pattern imprinted driveway may last even less time due to the maintenance required to keep them looking pristine.

It’s also worth considering that resin bound driveways are good permeable surfaces, so will drain well and keep water from pooling around your property. This will keep your property maintenance costs down, since pooling water or flooding around your home could cause damp in your walls which is a very expensive problem to fix.

Resin bound driveways are by far the most attractive type of driveway to have. There are no loose stones to sweep up, no weeds to pull out from the gaps, and there’s no extensive power washing required to keep them looking good. If you want a driveway that gives your home true kerb appeal and you value your time, resin bound driveways don’t seem that expensive.

The other factor that can make resin bonded driveways less expensive is that sometimes you can lay them on top of the existing surface. For example, if you already have a concrete or asphalt driveway that is in good condition with no large cracks, a driveway contractor may be able to lay the resin and aggregate mix straight over the top, which will cost much less money than if you have to dig up the existing driveway and start from scratch.

1. Prepare the base If you want your resin bound driveway to last a long time, you need to ensure that you prepare the base properly. Remove any block paving, grass or soil and dig down until you hit solid ground. Lay a sub-base of asphalt for good permeability. If you’re laying over the top of your current driveway, make sure that all cracks are increased into a ‘v’ shape with a saw and ensure the surface is dry and weed-free.
2. Mix the resin You must follow the instructions on the materials you have to the letter if you want the curing process to work. Usually batches come in ‘Part A’ and ‘Part B’. Keep the resin container secure and on a protective surface to avoid splashing, then mix Part A for 10-20 seconds at a slow speed with a helical bladed mixer. Add Part B and mix thoroughly at a slow speed for about 2 minutes until it’s blended together.
3. Mix the dried aggregates and sand with the resin Place a quarter of the aggregates into a mixer, then add the pre-mixed resin and start a stopwatch. You should then add the rest of the aggregates before slowly adding the sand. When you’re happy with that mix, stop the stopwatch. That time is the time that you need to spend mixing any other resin and aggregates to avoid colour variation.
4. Lay the mix on the surface Transfer the mix to the work area then plan a laying route. When the mix is laid out, use a very clean trowel to spread the mix. Clean it regularly during the process to avoid dragging aggregates out of place. Once the aggregates stop moving in a fluid movement and become solid, stop trowelling. Then you can polish the surface to give it an attractive shine.