Slab Paving in Dumbarton

Slab paving is a great material to use to create a sturdy shed base.

Start by measuring out the area where your shed is going to be. This needs to be the size of your shed, plus about 10-20cm extra each way. Mark it out with string and pegs, make sure it’s square, and dig it down to about 6cm deep.

Then create a sand and cement mixture and put a layer down, followed by your paving slabs. Make sure you start in one corner and use a rubber mallet and spirit level to make sure they’re as level as possible. Leave this to set and you’re ready to use your shed base.

Are you planning on investing in a new driveway for your home? If yes, then you’d probably want to know how much you’re going to incur to complete the project. In this guide, we’ll give you an idea of the cost of constructing a new driveway.

When it comes to driveway construction a larger part ( up to 80%) of the cost is made of the parts that are completely invisible to you - the sub base as well as the ground preparation, while the remaining cost of about 20 percent is required for the paving and other materials. As a result, there are multiple factors affecting the price of a driveway project. These includes the materials preferred, the level of work that’s required for the ground preparation as well as the complexity of the laying pattern or design. With this in mind, you’d have to schedule an appointment with two or more professional to obtain and compare their quotes.

Although there are many other options, but block paving happens to be a popular choice due to its cost effectiveness, visual appeal as well as being a hard wearing drive. The common choice for block paving I the Drivesett Tegula and the price usually starts from range between £30 to £35 per m2 and above. However if you’re looking for the conventional block paving with a modern twist, then the Marshalls coppice is a suitable option. The cost of the option usually starts from £25 to £30 per m2 and above. You can also opt for block paving in circle designs which gives you a better option to make an impression. Once you’re able to figure out the size of the paving area, you can roughly estimate what the cost of your driveway will be.

If you want to give your concrete paving slabs a new lease of life, it’s possible to paint them. This is a great option if your slabs are looking tired or you want a new look, but you don’t want to invest in new paving.

Before you go ahead, you need to make sure that your slab paving is clean and dry. And if it’s been sealed, you’ll need to strip this off. Make sure you get a paint that’s specifically designed for the job so you get the best results.

If you’re considering giving your home a quick facelift, laying of paving slabs for your outdoor living spaces might be a great way to start. It can be installed in some many parts of your home’s exterior from the pathways to driveways and from the yards to the patios. With proper training and experience, laying paving slabs is a very easy and quick process. However, the issue here is, how do you calculate the number of paving slabs you need? In this step by step guide, you’ll find all the information needed to help you get started. Once you’re able to get the accurate number of paving slabs, do ensure to include extras that’ll cover up for possible errors or damages.

Just like any other measurement task, it’ll be a lot easier when you know how as well as when you have the right tools to use for the job. To get started, you’ll need a tape measure, pen or pencil, pegs, string, hammer, paper and calculator.

• Draw a sketch of the area. This sketch will take note of the area’s length and width.

• Using strings and pegs, mark out the area to be paved

• Using a tape measure, take a measurement of the length and width of the space along the string lines and note them on the sketch.

• If the area is a drive make sure that the paved area is wide enough to accommodate the cars intended

• Multiply the length of the space by the width to get the area of the space.

• Once calculated, divide the total area of the space by the area of the single slab. This will give you an accurate number of the paving slabs you’ll require to complete your project.