Slab Paving in Fraserburgh

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

Are you planning on investing in a new driveway for your home? If yes, then you’d probably want to know how much you’re going to incur to complete the project. In this guide, we’ll give you an idea of the cost of constructing a new driveway.

When it comes to driveway construction a larger part ( up to 80%) of the cost is made of the parts that are completely invisible to you - the sub base as well as the ground preparation, while the remaining cost of about 20 percent is required for the paving and other materials. As a result, there are multiple factors affecting the price of a driveway project. These includes the materials preferred, the level of work that’s required for the ground preparation as well as the complexity of the laying pattern or design. With this in mind, you’d have to schedule an appointment with two or more professional to obtain and compare their quotes.

Although there are many other options, but block paving happens to be a popular choice due to its cost effectiveness, visual appeal as well as being a hard wearing drive. The common choice for block paving I the Drivesett Tegula and the price usually starts from range between £30 to £35 per m2 and above. However if you’re looking for the conventional block paving with a modern twist, then the Marshalls coppice is a suitable option. The cost of the option usually starts from £25 to £30 per m2 and above. You can also opt for block paving in circle designs which gives you a better option to make an impression. Once you’re able to figure out the size of the paving area, you can roughly estimate what the cost of your driveway will be.

To inexperienced people laying of paving slab isn’t much more than digging a little, purchasing little amount of mortar and pressing down the paving slabs. But how good would it have been if only it were that easy in real life? The truth is, in reality, laying paving slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. As a result, if you lack proper training or experience, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the paving slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

• Mix a layer of mortar for each paver.

• Apply the mixed mortar onto the sub base by using the trowel.

• Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.

• Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.

• Take a measurement of the gap between the pavers

• Repeat the above steps until all pavers have been perfectly laid

• Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.

• Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard bristled brush.

Some paving projects require you to cut paving slabs to make them fit into a smaller space. To do this, firstly you need to measure the slab and draw a line in pencil or chalk where you want to cut.

There are then several different ways you can cut the slab – you or your professional can choose the one you or they are most happy with. A hammer and chisel can work well, or a handheld saw. You can also use an angle grinder fitted with a stone-cutting disc.