Slab Paving in Lairg

Slab paving is a great material to use to create a sturdy shed base.

Start by measuring out the area where your shed is going to be. This needs to be the size of your shed, plus about 10-20cm extra each way. Mark it out with string and pegs, make sure it’s square, and dig it down to about 6cm deep.

Then create a sand and cement mixture and put a layer down, followed by your paving slabs. Make sure you start in one corner and use a rubber mallet and spirit level to make sure they’re as level as possible. Leave this to set and you’re ready to use your shed base.

If you’re considering giving your home a quick facelift, laying of paving slabs for your outdoor living spaces might be a great way to start. It can be installed in some many parts of your home’s exterior from the pathways to driveways and from the yards to the patios. With proper training and experience, laying paving slabs is a very easy and quick process. However, the issue here is, how do you calculate the number of paving slabs you need? In this step by step guide, you’ll find all the information needed to help you get started. Once you’re able to get the accurate number of paving slabs, do ensure to include extras that’ll cover up for possible errors or damages.

Just like any other measurement task, it’ll be a lot easier when you know how as well as when you have the right tools to use for the job. To get started, you’ll need a tape measure, pen or pencil, pegs, string, hammer, paper and calculator.

• Draw a sketch of the area. This sketch will take note of the area’s length and width.

• Using strings and pegs, mark out the area to be paved

• Using a tape measure, take a measurement of the length and width of the space along the string lines and note them on the sketch.

• If the area is a drive make sure that the paved area is wide enough to accommodate the cars intended

• Multiply the length of the space by the width to get the area of the space.

• Once calculated, divide the total area of the space by the area of the single slab. This will give you an accurate number of the paving slabs you’ll require to complete your project.

Some paving projects require you to cut paving slabs to make them fit into a smaller space. To do this, firstly you need to measure the slab and draw a line in pencil or chalk where you want to cut.

There are then several different ways you can cut the slab – you or your professional can choose the one you or they are most happy with. A hammer and chisel can work well, or a handheld saw. You can also use an angle grinder fitted with a stone-cutting disc.

To inexperienced people laying of paving slab isn’t much more than digging a little, purchasing little amount of mortar and pressing down the paving slabs. But how good would it have been if only it were that easy in real life? The truth is, in reality, laying paving slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. As a result, if you lack proper training or experience, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the paving slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

• Mix a layer of mortar for each paver.

• Apply the mixed mortar onto the sub base by using the trowel.

• Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.

• Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.

• Take a measurement of the gap between the pavers

• Repeat the above steps until all pavers have been perfectly laid

• Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.

• Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard bristled brush.