Slab Paving in Ramsgate

Do you want to install a new patio? If yes, then on top of the agenda will definitely be the cost of paving slabs. However providing a single and accurate estimate to the cost of your new patio is almost impossible as there are many factors that can influence what the price would be. These factors include the size of the area, the choice of stone, installations and lots more.

To get a more accurate estimate of your cost there’s is the need to look at some factors before calculation. These includes envisioning your patio as well as putting the drainage in mind. Firstly, you’ll need to decide where you want your patio to be - this should include considering whether you’ll get enough privacy sitting on your patio and more. If you’re able to identify where to put your patio, you’ll be able to have a clearer idea of the potential shape and size of the patio. Secondly, there’s a need to consider the drainage because failure to provide adequate drainage will only result in storing of water which leads to a development of algae or vegetation across your patio.

The material you opt for is also a huge determinant of your patio’s cost. When it comes to paving slabs you’ll only get what you pay for. Deciding to go for cheaper paving slabs will most likely lead to frequent staining, slippery surface, tough maintenance as well as constant cracking. Consequently, the act of cutting back on the cost of paving slabs will only you cost you more money in the long run. What’s more? If you have an existing patio you’d like to replace, then you’d probably need to include the cost of removing the existing one.

If you want to give your concrete paving slabs a new lease of life, it’s possible to paint them. This is a great option if your slabs are looking tired or you want a new look, but you don’t want to invest in new paving.

Before you go ahead, you need to make sure that your slab paving is clean and dry. And if it’s been sealed, you’ll need to strip this off. Make sure you get a paint that’s specifically designed for the job so you get the best results.

To inexperienced people laying of paving slab isn’t much more than digging a little, purchasing little amount of mortar and pressing down the paving slabs. But how good would it have been if only it were that easy in real life? The truth is, in reality, laying paving slabs does not only require you to prepare your sub-base painstakingly and mix your mortar using the appropriate materials, but you’d also have to work with accurate and precise paver placements to guarantee the patio’s longevity. As a result, if you lack proper training or experience, we’d recommend you hire the services of a seasoned professional who can guarantee the best results and also save you time and extra cash that may result from possible costly errors. In this guide, you’d gain more insight into the paving slabs laying process.

To get started, you’ll need sharp sand, cement, shovel, wheelbarrow, pointing trowel, rubber mallet, spirit level, jointing compound, hard-bristled brush and tarpaulin.

• Mix a layer of mortar for each paver.

• Apply the mixed mortar onto the sub base by using the trowel.

• Slot the first flag in place and ensure not to stain the paver’s surface with the mixed mortar.

• Using a rubber mallet, carefully tap the paver to the mortar bed. Once done, ensure the surface is even with a spirit level.

• Take a measurement of the gap between the pavers

• Repeat the above steps until all pavers have been perfectly laid

• Leave the pavers to dry for about 1 to 2 days. You can protect it using a tarpaulin if concerned about rain.

• Use the jointing compound to fill up the paver gaps to bind together the pavers. Ensure to wipe off any excess compound using the hard bristled brush.

Do you want to know the level of thickness a driveway concrete slab should be? Well, you are not alone! So many other home owners ask this question on a regular basis and reasonably so. In order to prevent cracks on your concrete over time, it’s crucial to ensure an even thickness across your driveway concrete. To determine the necessary thickness of your driveway concrete, there are some questions that must be answered. These includes:

• What’s the number of vehicles you expect to have on your driveway?

• Do you plan on parking heavy, industrial vehicles on it?

For a standard passenger vehicle driveway, you’d have a driveway spanning 8 to 9 feet in width as well as 15 to 18 feet for double width. The thickness for this type of driveway concrete is usually 4 inches of non-reinforced pavement. Ultimately, this enables you to park everyday family cars on it without having to worry about it cracking due to the car’s weight. Also in order to prevent cracks, it’s expected that the driveway should be sloped towards the street as this would make sure that there’s a run off of water especially for areas that experience lots of flooding. In addition, there’s also the need to install joints to prevent cracking. For the standard 4 inch thick driveway, these joints should be positioned about 10 feet apart.

Finally for parking heavy industrial vehicles, your concrete driveway is expected to be thicker in order to cope with the added weight. Typically, the concrete driveway will require a thickness of about 5 inches. The additional one inch may not sound much, but the fact is this can increase the load carrying capacity of the concrete driveway by up to 50 percent.