Block Paving in Petworth

The most commonly used driveway surfacing materials are gravel, asphalt, concrete and paving - which can be block, slabbed or patten imprinted. Take a look at our product information pages to help you decide which one to use and which one will look best for your driveway.

Are you worried there’s a slope on the area where your block paving is to be installed? Good news is, it’s very possible to lay block paving on a slope. However, this can be a very difficult task which should be done by a reliable professional ( especially if you lack proper training and experience) who can guarantee the best results, the first time and also help save you money from possible costly mistakes. This guide will provide you with everything you need about the slope block paving installation process. Let’s have a look!

• Demarcate The Walkway

To get started, you have to determine how and where you want your walkway to be while also determining the thickness of the paver. Ensure to choose the less sloppy area and utilize landscape paint to mark the area visibly.

• Prepare The Ground

Clear out all forms of dirts, roots, rocks and other debris on the soil. Once done, proceed to cutting the sods to the required length and put them somewhere close.

• Make Boundaries

There’s a need for landscape borders. Here, it’ll be easier to use plastics as boundaries for your lawn’s edges. Install them on the sides that have already been cut

• Apply A Level Of Gravel

Obtain the correct size of gravel and spread them evenly over the area to ensure a firm foundation for the pavers is formed. Makes sure that the rocks is at a minimum of 2 inches deep into the soil.

• Install The Block Pavers

Start from the centremost position of the pathway and work towards the sides until you’re able to cover every inch of the area.

• Apply A Layer Of Cement

Apply cement over the pavers and utilize a broom to sweep it and fill up all the gaps and spaces between the pavers. Then, press the pathway to be levelled using a compactor.

Can You Lay Block Paving On Top Of Concrete?

The replacement or improvement of your driveway is unarguably one of the most expensive projects you can undertake in the exterior of your home. When done by a true professional the results can be impressive and visually appealing, however you’d have to pay huge bucks to have this done. This is exactly the situation with block paving as it is not only time consuming, but also a lot more expensive when compared to other types of driveway.

A large chuck of this cost is associated with the removal of the existing driveway. So assuming your old driveway is concrete, can you simply pave over the existing concrete? If yes, will it save you money? The simple and short answer is yes. It’s in fact advisable to pave over concrete as this will not only add around 20% to your home’s value, but also make it look a lot more attractive and pleasing to the eye.

However, there are some problems associated with block paving over concrete. It may be better to remove the concrete in situations whereby the base is substandard. For instance, if the ground underneath the concrete is failing, there’ll most definitely be problems.

Also, there’ll be some issues with settling (not even the cracks). If your concrete is dropping little amounts every year, these can affect the blocks and ultimately lead to dropping of some sections of the block paving in such a way that they’ll no longer be on the same level as the other blocks. Giving a rise to the possibility of drainage issues, tripping hazard and lots more.

Other issues that may crop up can be triggered as a result of using the wrong size block height as well as totally ignoring or overlooking the undulations of the concrete.

How To Lay Block Paving

Do you wish to know how to install block paving? We’ve got you covered! Here, you’ll find a useful step by step guide that’ll provide you with all the necessary information to lay a wide range of block paving products available in the market today. You must, however, note that the installation of block paving can be a tricky affair and should not be attempted unless you have undergone a proper training or have a good experience in the field. If otherwise, we’d advise you to leave the task for a reliable block laying professional to guarantee the best results and also avoid making costly mistakes.

lDesign

• Draw up a design to perfectly suits your needs.

• Decide on the type of block as well as colour.

lExcavation

• Use a mini excavator or a JCB ( depending on the size of the job) to excavate the driveway.

• Identify and mark out the area to be excavated.

• Dug out the area until you reach a suitable level

• Ensure that the proposed finish level is 150mm underneath the damp proof course in any of the adjoining building’s brick.

lEdge Restraints

• Build a 100mm depth-thick concrete foundation with the help of a concrete mixer, 1 part cement and 6 parts ballast.

• Position the kerb unit on top of the level with a string line and spirit level.

• Use a trowel and rubber mallet to mortar the kerb unit to the foundation.

• Haunch the back of the kerb units in such a way that the concrete reach half way up the kerb’s rear.

lSubbase

• Put the crushed concrete in the edge restraints and ensure it’s at the desired level of 50mm.

• Use a vibrating plate to compact and level

lScreeding

• Apply a layer of sharp sand (to 50mm depth) and campact it using a vibrating plate.

• Apply second layer of sharp sand (to 20mm depth) on top of the first layer.

• Level the second layer to the correct falls.

lInstallation Of Paving

• Lay the block paving starting from the bottom of a slope.

• Ensure the blocks are placed at about 10mm to 15mm above the required finish level.

• Make sure the blocks used are between 3-5 packs as you proceed with your desired pattern. You may need to cut smaller block pieces to fill smaller gaps.

lFinishing Touches

• Clear out the area to ensure no debris is left on the blocks.

• Put kiln dried sand and brush across the whole of the area, ensuring the sands falls between the blocks’ joints.

• Compact the drive with the vibrating plate.

• Brush more kiln dried sand over the area and compact again

• Repeat the process until the joints are full of sand.